The snap ring fits into a groove on the lower end of the sink flange. When you’re working under the sink, it prevents the upper mounting bracket from falling off. Removing an old snap ring can be frustrating-unless you know this trick: Starting at the break in the ring, insert a thin-blade screwdriver between the ring and the flange. Pull down on the ring with the screwdriver’s blade and walk the blade around the ring. The ring will pop right off.
With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes ... full review
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
Place the garbage disposal on a wide, clean work surface and locate the rubber gasket. The old gasket should be peeled off, and the new gasket should be mounted in the same spot. Take extra care to make sure that it sits flat and that it pops into the lip. Now you are ready to re-install your garbage disposal. Plug the cord back in reconnect each of the drains to make sure that there are no leaks.
Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.
As a general rule of thumb, the heavier and bigger that a garbage disposal is, the more quietly it will operate – so long as it fits properly underneath your sink. Even though the sound dampening technology used in the design of garbage disposals has improved dramatically in the last 10 years, it is unrealistic to expect your garbage disposal to operate noise free. Under specific sinks, some disposals will be noisier than others due to the amount of vibration they produce. Ideally, you should look for a garbage disposal that features a nylon, insulated grinding chamber, like those produced by WasteKing.
When something blocks your disposal unit’s flywheel, you will start hearing a low humming sound, and you know you’ve got a jam. Un-jamming a garbage disposal is something that depends on the specific unit you own. Every single one has a function to shut off when they are stuck to the point of stalling the motor. This is so the motor doesn’t burn out. However, they are also designed so that anyone (and we mean anyone!) can remove whatever it is that is blocking your unit. Underneath every unit is a small slot, and pretty much all of them come with a tiny little wrench to match it. These are most commonly called hex-head wrenches. Yes, that little tool that you probably have no idea where it could possibly be has a very specific and important purpose. Mind blown, right?
Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services. If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.
Thank you for sharing this tutorial. My husband and I tried to fix our garbage disposal last week but we couldn’t get it to work. When we turn it on, it makes a humming noise, but nothing is blocking the blades. We might need to get a new disposal, but we’ll probably have a professional look at it before we decide. We’ll keep your tips on hand, just in case.
Installing a garbage disposal involves tapping into your home’s plumbing and electrical systems, and both systems need to be handled correctly to safely install your garbage disposal. Someone with a lot of experience can handle the job in 2 or 3 hours—or maybe even less. Attempting a garbage disposal installation without any training will likely take at least double the time required for a professional to install the garbage disposal.
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
Prior to testing the garbage disposal for leaks, unplug it at the wall outlet and turn off the power from the breaker box to prevent electrical shock. Then insert a watertight sink stopper into your sink drain and wipe the unit dry with a clean cloth. In any handy container, mix a few drops of food coloring into a few cups of water, and pour the dyed water onto the sink stopper to help you locate the leak.
STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!
I bought this two years ago when planning a kitchen remodel for our retirement home. Since I was doing the remodel myself, it took two years, working part time. During that period I managed to lose the instructions for this air switch. Thank you for providing them. Now I can install it on the front of my Ikea kitchen sink cabinet. When/if I ever am in a wheelchair or walker, I will still be able to easily reach the disposal switch. WARNING: If you have a toddler, mount this where they can't easily reach it and send a matchbox car down your sink disposal in an imaginary carwash.
Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.
But there is really only one rule you need to follow: Never put your hand or fingers down into the disposal, even if you think the disposal has been unplugged or its circuit has been shut off. If a disposal gets turned on accidentally while your fingers are in the opening, the likelihood is that you will end up with bruised fingers, not bloody amputation. But this is not a risk that is necessary in any way.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.