If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.

Some jams you can free and get the motor to spin and sound like it is working, but the blades are stuck in one position and can’t spin freely to do their job properly. This is very common problem – the motor works so we think everything is working. Not the case! This can lead to stoppages, food trapped in the disposal and a bad smell. These blades can’t be repaired. The disposal needs to be replaced.
Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.

This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.

For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.


• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
If you have a broken seal on the inside of your garbage disposal, you will see leaking coming from the bottom of your unit. Leaks that come from the bottom of your garbage disposal are usually attributed to cracks on the inside of the device. This is due to basic wear and tear overtime. To fix this issue, you’ll need simply invest in a new garbage disposal.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.
Dishwasher Connection: Some disposals are connected to the dishwasher drain pipe, which drains leftover food removed from dishes going through the wash cycle. Leaks can sometimes occur in the hose connections where the disposal hose attaches to the dishwasher.Leaks can also happen if the seal on the hose is compromised or the clamp on the hose isn’t tight enough. If the connecting hose seems to be the source of the leak, try tightening the connection or replacing the seal. If neither solutions work, or the hose is obviously cracked, you will need to replace the hose.
For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.

Many localities in the United States prohibited the use of disposers.[8] For many years, garbage disposers were illegal in New York City because of a perceived threat of damage to the city's sewer system. After a 21-month study with the NYC Department of Environmental Protection,[9] the ban was rescinded in 1997 by local law 1997/071, which amended section 24-518.1, NYC Administrative Code.[10]


My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.

Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.


Assuming that you have already given the disposal the time it needs to run and clear the garbage, you probably have a congested drain line. We don’t recommend using chemical drain cleaners with a garbage disposal. You will very likely just damage the unit and end up with a sink full of toxic chemicals that you’ll eventually be forced to clean out manually. If the blockage doesn’t go down with the good ol’ baking soda and vinegar remedy, then calling a John Moore professional is your best bet. He or she will know exactly how to properly remove the bolts, disconnect the drain trap and remove the trap and the discharge drain pipe, check for clogs and any other obstructions, and finally clear the blockage with the latest and best tools. (See our previous post about good steps you can take when your kitchen sink is clogged!)
If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
InSinkErator garbage disposals provide a convenient and environmentally-conscious alternative to sending leftovers to landfills. Capable wastewater treatment plants can even recycle food scraps into energy and fertilizer. Plus, using garbage disposals can significantly reduce the amount of trash sent to landfills and reduce greenhouse gas emissions.

STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
The garbage disposal in your kitchen sink is a convenient way to get rid of scraps and leftovers, but when a foreign object like a glass gets caught in it, it can jam the mechanism and stop it from working. Removing a glass from a garbage disposal involves removing any large pieces of glass; dislodging the glass by inserting a wrench or broom handle into the bottom or top of the disposal; vacuuming the disposal; resetting it; or if none of the other steps work, removing the disposal and shaking out all of the glass. Read the following steps to find out how to remove a glass from a garbage disposal.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.

Compared to the Sicilian Mafia's pyramidal structure, the Camorra has more of a 'horizontal' than a 'vertical' structure. As a result, individual Camorra clans act independently of each other, and are more prone to feuding among themselves. This however makes the Camorra more resilient when top leaders are arrested or killed, with new clans and organizations germinating out of the stumps of old ones. As the Galasso clan boss Pasquale Galasso once stated in court; "Campania can get worse because you could cut into a Camorra group, but another ten could emerge from it."[27]

Bathroom Plumbing Boca Raton Community Drain and Sewer Drain Cleaning Drain Clogs Electric Water Heaters Garbage Disposal Hot Water Heaters Hydro Jetting Jupiter Lake Park Lake Worth North Palm Beach Pipe Lining Pipe Relining Pipe Repair Pipe Replacement Plumber Plumbing Plumbing Installation Plumbing Leak Plumbing Maintenance Plumbing Repair Port St. Lucie Repiping Sewer Repair SEwer REplacement Slab Leak Stuart FL Tankless Water Heater Tankless Water Heaters Toilet Plumbing Toilet Repair Toilets Trenchless Pipe Lining Video Camera Pipe Inspection Water Filtration Water Heater Water Heater Installation Water Heater Maintenance Water Heater Repair Water Heaters Water Treatment Systems West Palm Beach


Many Camorra members and associates fled the internecine gang warfare and Italian Justice and immigrated to the United States in the 1980s. In 1993, the FBI estimated that there were 200 camorristi in the United States. Although there appears to be no clan structure in the United States, Camorra members have established a presence in Los Angeles, New York and Springfield, Massachusetts.[56] The Camorra is the least active of all the organized crime groups in the United States.[57] In spite of this, the US law enforcement considers the Camorra to be a rising criminal enterprise, especially dangerous because of its ability to adapt to new trends and forge new alliances with other criminal organizations.[58]

I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
We apologize in advanced for stating the obvious, but… garbage disposals absolutely do not last forever! No matter how well it’s made or how much money you spend, any appliance that is exposed to thousands of gallons of running water, dish soap, scraps of food, bones, and the rare (we hope) spoon or lime wedge that accidentally gets dropped into the drain is going to wear out in due time. A unit that’s working well should be able to handle a few scraps of veggies or apple slices in a matter of a couple of seconds. If your garbage disposal seems to take forever to accomplish a simple grinding job, makes a strange noise or emits a nasty smell, it may be time to install a new one.
One of the handiest appliances in your kitchen is probably something that you don’t think about very often, until it stops working. It’s your garbage disposer, and today I’m going to show you how to replace a garbage disposer under your kitchen sink. This project requires some moderate do-it-yourself skills, and it also requires turning off the electricity to the disposer at the electrical panel. But it’s really not that difficult, so let’s get started.
Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control

A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
Jarred Connections: Considering the garbage-disposal systems is located under the kitchen sink, and since the area under the kitchen sink is a common place for storing all sorts of things, it is fairly common for the unit to get bumped.If it gets hit hard enough, the unit can actually shift so that it is no longer sitting straight. Pipes can also get knocked around, causing the seals to lose effectiveness.
The majority of today’s garbage disposals are designed to dovetail with a sink’s drain outlet, which makes connecting the two components simple. There are a multitude of connection kits and adaptors available. Many models feature a power cord that is simply plugged into a nearby outlet to power the unit; however, when an outlet is not available, the unit must be hardwired, which can be significantly more expensive.

There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)

InSinkErator is a brand name that is well-known for their design and manufacturing of waste disposal systems and instant hot water dispensers. John Hammes founded the company in 1927 in Racine, Wisconsin, where their headquarters remain today. Hammes is credited with designing and producing the first “in sink” waste disposal system, and the InSinkErator is a play on the word “incinerator”. Currently, InSinkErator produces and markets garbage disposal systems under the Evolution and Badger Series brand names.
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
There you have it. If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.
Lowe's offers garbage disposals like the InSinkErator Evolution and Badger garbage disposals in various horsepower options. Models with lower horsepower tend to become jammed easily. What if your garbage disposal jams? No problem. Simply locate the hex socket in the center of the underside of the disposal. Grab a hex wrench, put it in the socket, and work it back and forth until you feel the blades loosen up. Once the blades are spinning freely, press the garbage disposal reset button. It's that easy.
×