We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:

In 2008, Italian police arrested three members of the Camorra crime syndicate on September 30, 2008. According to Gianfrancesco Siazzu, commander of the Carabinieri police, the three were captured in small villas on the coast of Naples. All three had been on Italy's 100 top most wanted list. Police seized assets valued at over 100 million euros and also weapons, including two AK-47 assault rifles that may have been used in the shooting of six Africans on September 18, 2008. Police found pistols, Carabinieri uniforms and other outfits that were used to disguise members of the operation. During the same week, a separate operation netted 26 additional suspects in Caserta. All were believed to belong to the powerful Camorra crime syndicate that operates in and around Naples. The suspects were charged with extortion and weapons possession. In some cases, the charges also included murder and robbery. Giuseppina Nappa, the 48-year-old wife of a jailed crime boss, was among those arrested. She is believed to be the Camorra's local paymaster.[46]
Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]

Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.

Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.


STEP 3 – Clear out the disposal to remove any bits of hard foods, bone shards or other fibrous gunk that may be preventing the grinding blades from rotating and pulverizing your discarded food. Use a tool (a pliers, wooden spoon, etc.) to do this. Putting your hand in situation where whirling blades of destruction are nearby is never a good idea. (That is what I’ve heard anyway.)

There you have it. If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.
Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
Kitchen waste disposal units increase the load of organic carbon that reaches the water treatment plant, which in turn increases the consumption of oxygen.[28] Metcalf and Eddy quantified this impact as 0.04 pound of biochemical oxygen demand per person per day where disposers are used.[29] An Australian study that compared in-sink food processing to composting alternatives via a life cycle assessment found that while the in-sink disposer performed well with respect to climate change, acidification, and energy usage, it did contribute to eutrophication and toxicity potentials.[30]
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.

Garbage Disposal

×