If the leak occurred in either of the two connections (smaller = dishwasher, larger = sewer) exiting the side of your disposal unit, it’s a pretty straightforward fix. Loosen the metal clamps on these hoses and make sure the rubber gaskets inside are not falling apart. If needed, replace these gaskets. Reattach the hoses and re-clamp the connections with new metal clamps.
Some types of food remains are not easy to grind in a disposer. Do not put fibrous food items into your disposal. Help grind these items by putting in a few small bones or large ice cubes to the disposal. If the disposer won’t grind it up then turn off the disposer and remove the item with a pair of tongs. When using your disposer, make sure that the disposal is running with good water flow. Good water flow carries the waste down the drain line. Using too little water can create a clogged drain.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
One of the Camorra's strategies to gain social prestige is political patronage. The family clans became the preferred interlocutors of local politicians and public officials, because of their grip on the community. In turn, the family bosses used their political sway to assist and protect their clients against the local authorities. Through a mixture of brute force, political status, and social leadership, the Camorra family clans imposed themselves as middlemen between the local community and bureaucrats and politicians at the national level. They granted privileges and protection, and intervened in favour of their clients in return for their silence and connivance against local authorities and the police. With their political connections, the heads of the major Neapolitan families became power brokers in local and national political contexts, providing Neapolitan politicians with broad electoral support, and in return receiving benefits for their constituency.[26]

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”

Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water

Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.


Installing a garbage disposal involves tapping into your home’s plumbing and electrical systems, and both systems need to be handled correctly to safely install your garbage disposal. Someone with a lot of experience can handle the job in 2 or 3 hours—or maybe even less. Attempting a garbage disposal installation without any training will likely take at least double the time required for a professional to install the garbage disposal.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite. 

Fast Garbage Disposal Replacement

×