Wrap plumbing tape around the threads of the sink drain where the disposal crews to the sink and the drain threads on the side of the disposal for the drain pipe. Screw the disposal back in under the sink. Screw the drain pipe back to the disposal. Tighten with the pipe wrench. Turn on the water to check for leaks and plug the disposal back in. Turn on the power switch to make sure disposal is running properly.
Start by turning off and unplugging the garbage disposal. Next, you’ll need the wrench that came with your disposal. If you don’t have it, you can buy a replacement in a hardware store that sells your disposal brand. Find the hex-shaped opening at the bottom of the disposal unit. Turn the wrench clockwise to dislodge whatever’s blocking the flywheel. When the object dislodges, you’ll feel the flywheel start to turn easily. Reset the disposal and run cold water while quickly turning it on and off repeatedly.
After all this, if your garbage disposal still refuses to turn on, it’s likely just broken. The motor could be burned out or there could be another related problem. If that’s the case, now is the time to get a new unit. Contact a plumber for garbage disposal replacement. If you live in the Pittsburgh area, contact Terry’s Plumbing. We’ll be happy to come out to your home, diagnose the problem with your garbage disposal, and replace the unit if necessary. To find out more, call us today at (412) 364-9114.
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.
Garbage disposals first appeared in households in the 1930's and 1940's. These appliances, which are installed under a kitchen sink, can make a cook's life easier by trapping and shredding food waste items, allowing it to pass through the plumbing system. Although these popular appliances make cooking and cleaning much more convenient, they do require regular maintenance to keep them running at optimal performance. When it is time to replace your garbage disposal's blades, you can save time and money by doing it yourself.
As the saying goes, an ounce of prevention is worth a pound of cure; in other words, take care of your garbage disposal to prevent leaks from happening. Proper use, regular maintenance and frequent inspections for leaks will keep your disposal in top working order. If you experience any water leaks or burst pipes, please call us and we will be happy to help.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.
A garbage disposal unit (also known as a garbage disposal, waste disposal unit, garbage disposer, or in Canadian English a garburator) is a device, usually electrically powered, installed under a kitchen sink between the sink's drain and the trap. The disposal unit shreds food waste into pieces small enough—generally less than 2 mm (0.079 in)—to pass through plumbing.
Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.
There you have it. If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
Proper use of a garbage disposal can stave off future leaks. So remember to grind only soft foods; hard items such as bones, apple cores, or raw potatoes can dislodge or damage the internal seals. Run cold water through the sink drain before and after food disposal to keep solid fats from congealing into gunk (which can deteriorate the sink flange and cause leaks). Finally, inspect your disposal for leaks—at least twice a year using the dyed-water test—to catch and repair minor leaks before they lead to water-damaged sink cabinets or kitchen floors.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.
Dispose orange peels, or any citrus rinds, to freshen the disposal and keep it smelling clean, but cut them into slices first as large pieces of citrus peel, e.g. half a lime, can jam a disposal. You can also use pieces of citrus fruit that may be too old to consume, as long as they're not too spoiled to smell nice. You can freeze these pieces first, if you wish.
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”