A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.
Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
Most blog writers make money from the links they include, so if someone is reading this and decides to click on a link and purchase the item, they receive a small sales commission per se. Mind you it takes hundreds to thousands of these blogs ranking high in google searches (I’m sure you have an issue with most people using googleopoly as well) in order to make any real money at it, but until other brands get on the bandwagon and pay instead of hoping for free advertising, great bloggers will continue to use what pays the bills. Or at least kicks you back a free tank of gas or two a year.
With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes my life. I can put bones, and tough food products down the disposal, and it makes cooking really simple. Go figure.
Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ... More + Product Details Close