Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.


I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.

The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.
STEP 4 – If you must use your hands (again, not advised) to pull out all that funky goo, see STEP 2. The disposal must be powered off and unplugged. No exceptions. Not even on a double-dog dare. Also, make sure your hand will actually fit into the opening so that you can eventually remove your hand from the opening. You may need your hand later. If you think it is going to be a tight fit, I’d suggest that you not try it all. You’ve been warned.

We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?
When rubber gaskets age, they can develop leaks. The gasket can dry up, crack, and leak when it is repeatedly exposed to long periods of disuse where no water is present in the drain pipe. Should an older garbage disposal be removed and then placed back, it will require a new rubber gasket to again achieve a watertight seal. Moreover, if a gasket is not evenly locked on all three sides, then it will develop a leak.
The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
The Camorra has proven to be an extremely difficult organization to fight within Italy. At the first mass trial against the Camorra in 1911–12, Captain Carlo Fabroni of the Carabinieri gave testimony on how complicated it was to successfully prosecute the Camorra: "The Camorrist has no political ideals. He exploits the elections and the elected for gain. The leaders distribute bands throughout the town, and they have recoursed to violence to obtain the vote of the electors for the candidates whom they have determined to support. Those who refuse to vote as instructed are beaten, slashed with knives, or kidnapped. All this is done with assurance of impunity, as the Camorrists will have the protection of successful politicians, who realize that they cannot be chosen to office without paying toll to the Camorra."[36]

One last thought - Beef bones? I see that Consumer Reports tests these things by measuring the fineness of the grind using beef bones. Do people really put beef bones down a garbage disposal on purpose? You might think I'm babying mine, or maybe that's why I didn't have excessive vibration when I use it, but I'll put the beef bones in the trash and grind up the rest of the stuff with this and be just fine for many years to come, I hope!
This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.

If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.

Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
×