If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”
Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF! Failing to do so will put you at risk of SERIOUS INJURY. Also, if possible avoid placing your hands directly near the blades at the disposal. If you can, instead use a tool to wedge out items or check the blades for blockage.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.
The easiest way to apply that force is to squeeze them together using tongue-and-groove pliers, such as Channellocks. You’ll need medium or large pliers to do this. Unlike prying on the lower ring with a screwdriver or hex wrench-the method recommended in most instruction sheets-squeezing can’t disturb the position of the sink flange and cause it to leak. Plus, it’s easier on the wrists.
The Camorra (Italian: [kaˈmɔrra]; Neapolitan: [kaˈmorrə]) is an Italian Mafia-type crime syndicate, or secret society, which arose in the region of Campania and its capital Naples. It is one of the oldest and largest criminal organizations in Italy, dating back to the 17th century. Unlike the pyramidal structure of the Sicilian Mafia, the Camorra's organizational structure is more horizontal than vertical. Consequently, individual Camorra clans act independently of each other, and are more prone to feuding among themselves.
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.