If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
Like most appliances with moving parts, all kinds of stuff can go wrong in your disposal, for all sorts of reasons. Luckily, unlike many appliances, most disposals can be quickly and relatively easily fixed, as long as you’re careful and do your research. The next time you experience one of the following problems, follow these instructions and see if you can’t get things moving again.
To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.
InSinkErator garbage disposals provide a convenient and environmentally-conscious alternative to sending leftovers to landfills. Capable wastewater treatment plants can even recycle food scraps into energy and fertilizer. Plus, using garbage disposals can significantly reduce the amount of trash sent to landfills and reduce greenhouse gas emissions.
Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.
Lowe's offers garbage disposals like the InSinkErator Evolution and Badger garbage disposals in various horsepower options. Models with lower horsepower tend to become jammed easily. What if your garbage disposal jams? No problem. Simply locate the hex socket in the center of the underside of the disposal. Grab a hex wrench, put it in the socket, and work it back and forth until you feel the blades loosen up. Once the blades are spinning freely, press the garbage disposal reset button. It's that easy. 

Chartered by entrepreneur Lowell Harrelson and Long Island mob boss Salvatore Avellino, it set sail on March 22 from Islip, New York,[2] escorted by the tugboat Break of Dawn and carrying 3,168 tons of trash headed for a pilot program in Morehead City, North Carolina, to be turned into methane. The barge was docked at Morehead City, until a WRAL-TV news crew, acting on a tip, flew by helicopter to the coast to investigate. Action News 5 Reporter Susan Brozek broke the story on the 6 p.m. news on April 1, 1987, and North Carolina officials began their own investigation, which resulted in an order for the Mobro to move on.
Most plumbing problems associated with holiday parties are caused by improper plumbing maintenance and overestimations of your plumbing system’s abilities. Although it’s best if you have a professional plumber inspect your system before any large gathering, many plumbing problems can be prevented with a little knowledge and preparation before the big day. Remember, the best offense is a good defense. Schedule annual plumbing maintenance to keep your entire plumbing system healthy and efficient. Current problems will be addressed and future problems will be detected.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.
Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.

Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!
But there is really only one rule you need to follow: Never put your hand or fingers down into the disposal, even if you think the disposal has been unplugged or its circuit has been shut off. If a disposal gets turned on accidentally while your fingers are in the opening, the likelihood is that you will end up with bruised fingers, not bloody amputation. But this is not a risk that is necessary in any way.

Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
To reseal the leaky flange, you must first detach the garbage disposal. Start by loosening the screws securing the main drain pipe to the disposal, then loosen the screws in the metal clamp securing the dishwasher hose to the disposal and detach the drain pipe and dishwasher hose from the disposal. Loosen the screws in the mounting ring that connects the disposal to the metal mounting assembly beneath the sink, then pull down the disposal and carefully set it on a clean, dry surface. Loosen the bolts in the mounting assembly with a wrench, then pull down the mounting assembly and set it near the disposal.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
×