SquareTrade Protection Plans are only valid for new or Amazon certified refurbished products purchased at Amazon in the last 30 days. By purchasing this Protection Plan you agree to the Protection Plan Terms & Conditions (http://www.squaretrade.com/terms-standard). Your Protection Plan Terms & Conditions will be delivered via email within 24 hours of purchase
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.

I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.

I thought that this might be underpowered (my last one almost had double the power, after all), but it has plenty of power to eat through whatever you throw at it. I don't dump EVERYTHING down the drain, but it takes what I give it with no problems. And the last garbage disposal was loud and raucous--yes, raucous. But this one is a pleasure. When you flip the switch, it makes a reassuring hum. It sounds more like a fine piece of machinery than a couple of animals fighting to the death inside my sink (like my old disposer).
Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
One of the Camorra's strategies to gain social prestige is political patronage. The family clans became the preferred interlocutors of local politicians and public officials, because of their grip on the community. In turn, the family bosses used their political sway to assist and protect their clients against the local authorities. Through a mixture of brute force, political status, and social leadership, the Camorra family clans imposed themselves as middlemen between the local community and bureaucrats and politicians at the national level. They granted privileges and protection, and intervened in favour of their clients in return for their silence and connivance against local authorities and the police. With their political connections, the heads of the major Neapolitan families became power brokers in local and national political contexts, providing Neapolitan politicians with broad electoral support, and in return receiving benefits for their constituency.[26]

The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.
The size of the motor in the garbage disposal directly correlates to the units grinding ability. Garbage disposals typically have between 1/3-1 horsepower motors. Choose the correct horsepower based on the waste that you need to remove. 1/3 horsepower units will help tackle tasks like grinding vegetables easily, but more power is recommended if disposing a large quantity of food waste such as, vegetables and harder to grind meats.
You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.
Modern garbage disposal units connect to dishwasher drainpipes.  This enables dishwashers to expel leftover food scraps and residue that would otherwise accumulate in the dishwasher unit.  A common source of leaks is the area where your dishwasher and garbage disposal connect.  These leaks most often occur when the hose’s clamp is not secure enough and when the dishwasher hose cracks.  To fix this issue, simply replace the cracked section of the hose or tighten the clamp.
Español: limpiar un triturador de basura, Português: Limpar um Triturador de Alimentos, Italiano: Pulire un Tritarifiuti da Lavandino, Deutsch: Den Küchenabfallzerkleinerer reinigen, Français: nettoyer votre broyeur d'évier, 中文: 清洁垃圾处理器, Русский: почистить утилизатор отходов, Bahasa Indonesia: Membersihkan Saluran Pembuangan Sampah, Nederlands: Je afvalvermaler schoonmaken, العربية: تنظيف مصرف النفايات
One of the handiest appliances in your kitchen is probably something that you don’t think about very often, until it stops working. It’s your garbage disposer, and today I’m going to show you how to replace a garbage disposer under your kitchen sink. This project requires some moderate do-it-yourself skills, and it also requires turning off the electricity to the disposer at the electrical panel. But it’s really not that difficult, so let’s get started.
Our most affordable large-capacity model ready to tackle Our most affordable large-capacity model ready to tackle meals of up to 750 persons with its powerful 3 HP motor. Like all InSinkErator food service disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as large banquet facilities ...  More + Product Details Close

Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.


Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
Loosen the nut securing the rest of the assembly. Just below the sink flange where the drain empties into the garbage disposal you’ll see a circular plastic piece similar in appearance to the mounting ring. Insert the tip of a screwdriver into one of the lugs on this piece and rotate it in a counterclockwise direction. Pull the nut away and set it aside.[9]
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
I hope this helps someone and encourages others to get the product. I think it is a great product and many of the poor reviews are because people didn't know how to use the mounting system. I gave it 4 stars because it doesn't have any tips in trouble shooting for when it leaks out the bottom. It should at least say to look at the drain hose and that it may be leaking inside from there and only appear to be leaking from the bottom. I also think Waste King should have made a video to show the EZ mount system. I mean it took me less than 10min. to do it all. Lastly, I don't like the click it can make when it turns on. While lots of people mention this and the directions say it's normal it is not "standard" in the garbage disposal business, meaning most don't make this noise. It can be startling and sound like something metal is in your disposal. While it is normal for their units, I still don't like it. It will take getting used to and then what if something metal is in my disposal will I think there isn't and that it's the click. That could cause damage very quickly if I think it's nothing and it is something.
Aside from the reviews I’ve put together, I haven’t forgotten about people who are having issues with their current food waste disposer. Below you will find some links to the information pages I’ve put together that will help you fix problems you might already have. For those of you that are confused over how to unclog a waste disposal unit, take a look at this page. On the same page, we also discuss waste disposal units that won’t power up and units that are leaking.

The origins of the Camorra are not entirely clear. It may date back to the 17th century as a direct Italian descendant of a Spanish secret society, the Garduña, founded in 1417. Officials of the Kingdom of Naples may have introduced the organization to the area, or it may have grown gradually out of small criminal gangs operating in Neapolitan society near the end of the 18th century.[3] However, recent historical research in Spain suggests that the Garduña never really existed and was based on a fictional 19th century book.[4]
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]
×