Whether you repaired or replaced the leaking garbage disposal, test for any missed problem spots. Wipe the unit dry with a clean cloth, then unplug the sink drain (if plugged) and pour a few cups of dyed water into the drain once more. Use a flashlight to inspect the entire unit. If you don’t observe a leak, turn on the power to the disposal from your breaker box and plug in the disposal at the wall outlet.
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
But there is really only one rule you need to follow: Never put your hand or fingers down into the disposal, even if you think the disposal has been unplugged or its circuit has been shut off. If a disposal gets turned on accidentally while your fingers are in the opening, the likelihood is that you will end up with bruised fingers, not bloody amputation. But this is not a risk that is necessary in any way.

Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services.  If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
Knowing the difference between what can go down the disposal and what should go into the trash can save you an emergency call to the plumber. This is especially pertinent during the holidays when the kitchen is filled with people and the sink with dirty dishes. Practice these three everyday maintenance tips to help you maximize the lifespan of your garbage disposal.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.
To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.
If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]

Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.


I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×