If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).
Run a few trays of ice cubes, orange peels and salt through the disposal to remove odors and keep your disposals clean. For really tough odors, add 1/2 cup of baking soda and 1/2 cup of vinegar and let it stand for 15 minutes before rinsing. Also, running ice through the disposal will actually sharpen the teeth, keeping foods from getting stuck in the unit.
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
If the source is not a connection from above then your disposal needs to be replaced. Try cupping your hands around the very top under the sink while running water. The ring that seals the gasket turns clockwise to tighten. The only other repairable leak would be where the piping comes out the side. There can also be a smaller dishwasher drain hose above that.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.

Some jams you can free and get the motor to spin and sound like it is working, but the blades are stuck in one position and can’t spin freely to do their job properly. This is very common problem – the motor works so we think everything is working. Not the case! This can lead to stoppages, food trapped in the disposal and a bad smell. These blades can’t be repaired. The disposal needs to be replaced.

If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.


Run your garbage disposal for longer each time you use it. A mistake many people make is turning off their garbage disposal as soon as the grinding noises stop. It is better to leave the garbage disposal on (with the water running) for several seconds after the grinding noises subside, as there may still be small particles in the disposal unit which have not yet been cleared away.
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.
The evolution into more organized formations indicated a qualitative change: the Camorra and camorristi were no longer local gangs living off theft and extortion; they now had a fixed structure and some kind of hierarchy. Another qualitative leap was the agreement of the liberal opposition and the Camorra, following the defeat in the 1848 revolution. The liberals realized that they needed popular support to overthrow the king. They turned to the Camorra and paid them, the camorristi being the leaders of the city’s poor. The new police chief, Liborio Romano, turned to the head of the Camorra, Salvatore De Crescenzo, to maintain order and appointed him as head of the municipal guard.[11] The Camorra effectively had developed into power brokers in a few decades.[9] In 1869, Ciccio Cappuccio was elected as the capintesta (head-in-chief) of the Camorra by the twelve district heads (capintriti), succeeding De Crescenzo after a short interregnum.[12] Nicknamed 'The king of Naples' ('‘o rre 'e Napole) he died in 1892.[13][14]
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
Built-in trash compactors fit snuggly into your kitchen cabinetry. Having a built-in compactor means you have one less appliance occupying precious floor space. A convenient toe pedal opener lifts the top open for easy hands-free opening, and a removable drawer make it easy to clean and empty the compactor. Shop for new garbage disposals and trash compactors from JCPenney today!
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.

A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
I'm not what you'd call a handyman, although I've been working to get better at that. I will now at least try a home project before passing on it. So, when our 15-year garbage disposal died I had another opportunity. I determined our old unit to be a Badger 5 1/2 HP (this exact item). I didn't have time to wait for the item to arrive from Amazon so I went to Home Depot and coughed up an extra $20 for the Badger 500 - Home Depot's branded version of this item. They are identical except for the name & sticker.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
Badger Series garbage disposals are the choice of homeowners looking for hard-working helpers in the kitchen that are as tough on food waste as they are easy on the wallet. The value and price is unbeatable. A powerful, 1/2 HP Dura-Drive motor powers the Badger 5 through your food waste including: vegetables, fruits, leftovers, egg shells, celery stalks, and small bones.

Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.


When something blocks your disposal unit’s flywheel, you will start hearing a low humming sound, and you know you’ve got a jam. Un-jamming a garbage disposal is something that depends on the specific unit you own. Every single one has a function to shut off when they are stuck to the point of stalling the motor. This is so the motor doesn’t burn out. However, they are also designed so that anyone (and we mean anyone!) can remove whatever it is that is blocking your unit. Underneath every unit is a small slot, and pretty much all of them come with a tiny little wrench to match it. These are most commonly called hex-head wrenches. Yes, that little tool that you probably have no idea where it could possibly be has a very specific and important purpose. Mind blown, right?


The government has made an effort to combat the Camorra's criminal activities in Campania. The solution ultimately lies in Italy's ability to offer values, education and work opportunities to the next generation. However, the government has been hard pressed to find funds for promoting long term reforms that are needed to improve the local economic outlook and create jobs.[40] Instead, it has had to rely on limited law enforcement activity in an environment which has a long history of criminal tolerance and acceptance, and is governed by a code of silence or omertà that persists to this day.[41]

Garbage disposals aren’t exactly quiet, but the device shouldn’t make a terrible screeching noise either. If your appliance is guilty of shrill sounds, there are a few potential causes. The grates could have shifted causing the device to move incorrectly, or the motor could be worn out. In either case, this usually occurs when a garbage disposal is at the end of its life, so replacement is a good option.

Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
If the leak occurred in either of the two connections (smaller = dishwasher, larger = sewer) exiting the side of your disposal unit, it’s a pretty straightforward fix. Loosen the metal clamps on these hoses and make sure the rubber gaskets inside are not falling apart. If needed, replace these gaskets. Reattach the hoses and re-clamp the connections with new metal clamps.

Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.
I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
To fix this problem, turn off the disposal, fill the sink halfway full with soapy water, and use a cup plunger to plunge the kitchen sink for 30 seconds to one minute. If you cleared the clog, the water in the sink should start draining at a normal pace again. If you’re still have issues, you might have to remove the P-trap under the sink to get at the clog with a snake.

Most garbage disposal manufacturers provide a range of models to choose from with ever-increasing power ratings. If you do a ton of cooking and use your disposal frequently, then spending a little extra on a 3/4 or 1 horsepower disposal will absolutely be worth the money. Not only do the more powerful units shred through food scraps much easier, but they can also handle harder objects such as bones or meat scraps that might jam a smaller, weaker disposal. As mentioned before, powerful disposals are less noisy and they tend to have only occasional damages. However, one downside of having larger, more powerful disposal is that they will require more space. No matter what your habits, likes, and dislikes are, it’s always best to consult with a John Moore tech before buying a new disposal to make sure it will fit under your sink and perform how you need it to.


While you’re inspecting your drain lines, also look to see if you see wear and tear. Over the years, drain lines can sprout leaks and cracks that can lose water. If you notice that your lines look pretty worn, you may want to have them replaced. Again, if you are inexperienced with home improvement projects, it’s best to call a professional to tackle the job.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.

Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.
Garbage disposals help us get rid of food waste, so it’s not surprising that the appliance may be susceptible to gross smells. A capful of bleach or grinding up citrus peels can help eliminate any foul odors coming from your garbage disposal. However, if nothing seems to help your appliance in the smell department, it may be catching food particles within its crevices. We recommend disassembling your garbage disposal to clean it, or replacing it if it’s old.
Russian activists have come under increasing pressure since Putin returned to office in 2012. Protests have been relatively scarce after the 2011-2012 Bolotnaya demonstrations in response to election fraud. Long-standing nongovernmental groups working on environmental and human rights issues, which relied in part on funding from abroad, have been labeled “foreign agents” by Russia’s Ministry of Justice.
Locate the leak. Wipe off the disposal unit with a dry rag. Run water into the unit and turn it on. There are four places where the disposal unit may leak. At the top main seal, at the drain pipe, at the optional dishwasher inlet or along the garbage disposal body. Notice where the water is coming from. If the unit is wet at the very top, the main seal is leaking. If the area beneath the drain pipe is wet, the gasket is leaking. If the hose from the dishwasher feed drips, the hose or clamp may be faulty. If water is running out the bottom of the unit but the inlets and outlet are dry, the unit itself has developed a leak and must be replaced.
Unlike the Sicilian Mafia, which has a clear hierarchy and a division of interests, the Camorra's activities are much less centralized. This makes the organization much more difficult to combat through crude repression.[39] In Campania, where unemployment is high and opportunities are limited, the Camorra has become an integral part of the fabric of society. It offers a sense of community and provides the youth with jobs. Members are guided in the pursuit of criminal activities, including cigarette smuggling, drug trafficking, and theft.[40]
A garbage disposal unit (also known as a garbage disposal, waste disposal unit, garbage disposer, or in Canadian English a garburator) is a device, usually electrically powered, installed under a kitchen sink between the sink's drain and the trap. The disposal unit shreds food waste into pieces small enough—generally less than 2 mm (0.079 in)—to pass through plumbing.[1]
×