If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.
Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.
A continuous feed model features a switch that is generally mounted on the wall nearby. In rarer cases, an air pressure switch may be mounted on the countertop. These air pressure switches are considered safer than traditional flip switches because they guard against shock by isolating the electrical system away from the sink’s source of water. Batch feed garbage disposals do not require the installation or use of a switch. Safety codes in your community will dictate how far away from the sink the electrical switch must be located.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.

Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.

Update: As an aside, I also learned from my research that the best way to clean my disposal is to use citric acid. Having previously had no idea what citric acid was used for, I decided to order some from Amazon, going with the brand my sister uses: Citric Acid Powder - Ultra Fine Pure Powdered Crystals - Natural Preservative Food Grade Quality (16 oz) and gave it a whirl after 3 months of using my disposal. I let the citric acid sit with some water in the disposal for about ten minutes, and then I let it run for a solid 2 minutes. I repeated the procedure a few times and after about 30 minutes—wow, all the leftover gunk and food was flushed out of the disposal, leaving it clean with a very mild citrus scent. I feel like I’m becoming a real DIY at home kind of guy.


2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.

A broken garbage disposal makes tackling your to-dos an unnecessary challenge, which is why the experts at Sansone want to help. Whether your garbage disposal is leaking, clogged, humming, or completely stuck, we can repair the issue or replace your garbage disposal entirely. Contact us today with any plumbing questions or schedule an appointment that’s convenient for you by phone or on our website.


If you can hear your disposal’s motor humming, but the disposal won’t grind, sounds loud, or starts and stops, it’s probably because something jammed it. Disposals jam when something gets lodged in the “flywheel,” which is what the disposal’s rotating plate is called. You can fix it yourself, but remember: NEVER stick your hand down the garbage disposal. Ever. Seriously.
Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
Most blog writers make money from the links they include, so if someone is reading this and decides to click on a link and purchase the item, they receive a small sales commission per se. Mind you it takes hundreds to thousands of these blogs ranking high in google searches (I’m sure you have an issue with most people using googleopoly as well) in order to make any real money at it, but until other brands get on the bandwagon and pay instead of hoping for free advertising, great bloggers will continue to use what pays the bills. Or at least kicks you back a free tank of gas or two a year.
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Garbage Disposal Repair or Replacement

×