Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
The snap ring fits into a groove on the lower end of the sink flange. When you’re working under the sink, it prevents the upper mounting bracket from falling off. Removing an old snap ring can be frustrating-unless you know this trick: Starting at the break in the ring, insert a thin-blade screwdriver between the ring and the flange. Pull down on the ring with the screwdriver’s blade and walk the blade around the ring. The ring will pop right off.
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
Manufactured in the United States, Waste King garbage disposals have won much praise for their energy efficient design. Waste King offers a wide range of garbage disposers for both residential and commercial settings. In the early 2000s, Waste King refocused their sights on providing unparalleled customer service and quality products, and their warranties are the current industry standard that others are measured by.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
Garbage Disposal Repair or Replacement