Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
Has a dual outlet to connect two appliances instead of one. You can connect your household waste disposal and a hot water dispenser (if you want). The power switches between the 2 outlets. When you press the switch to run the disposal, the water dispenser will be turn off. Once you press again to power off the disposer, the water dispenser will be turn on. Only one outlet is active at all times.

Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.


Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]

Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Español: limpiar un triturador de basura, Português: Limpar um Triturador de Alimentos, Italiano: Pulire un Tritarifiuti da Lavandino, Deutsch: Den Küchenabfallzerkleinerer reinigen, Français: nettoyer votre broyeur d'évier, 中文: 清洁垃圾处理器, Русский: почистить утилизатор отходов, Bahasa Indonesia: Membersihkan Saluran Pembuangan Sampah, Nederlands: Je afvalvermaler schoonmaken, العربية: تنظيف مصرف النفايات

Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.

Russian activists have come under increasing pressure since Putin returned to office in 2012. Protests have been relatively scarce after the 2011-2012 Bolotnaya demonstrations in response to election fraud. Long-standing nongovernmental groups working on environmental and human rights issues, which relied in part on funding from abroad, have been labeled “foreign agents” by Russia’s Ministry of Justice.

3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.
Even the most trustworthy garbage disposal will develop a leak from time to time; however, just because your food waste disposer has developed a leak does not necessarily mean that it needs to be replaced. Doing a little bit of investigating and troubleshooting before deciding to run out and buy a new garbage disposal can mean the difference between spending $10.00 for a replacement and $100.00+ to replace the entire unit.

Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water


Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.

The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.


Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.
Another method for cleaning and deodorizing your disposal unit is to sprinkle some baking soda in your unit and rinse it with about a cup of vinegar. This will create the bubbling “volcano effect” that kids love to watch so invite them in on this cleaning project. After allowing your mixture to sit for about 5 minutes, run hot water down the disposal until everything is thoroughly rinsed.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
Kitchen waste disposal units increase the load of organic carbon that reaches the water treatment plant, which in turn increases the consumption of oxygen.[28] Metcalf and Eddy quantified this impact as 0.04 pound of biochemical oxygen demand per person per day where disposers are used.[29] An Australian study that compared in-sink food processing to composting alternatives via a life cycle assessment found that while the in-sink disposer performed well with respect to climate change, acidification, and energy usage, it did contribute to eutrophication and toxicity potentials.[30]
The 2 800 RPM motor-powered dual stainless-steel swivel The 2 800 RPM motor-powered dual stainless-steel swivel impellers built into this GE 1/2 HP Continuous-Feed Garbage Disposal join forces with a 2-level pre-cutter to make it easy to grind undesirable waste into easily drainable particles. The disposer's large-capacity disposer chamber is comprised of a cold-rolled carbon steel armature shaft ...  More + Product Details Close
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
Another method for cleaning and deodorizing your disposal unit is to sprinkle some baking soda in your unit and rinse it with about a cup of vinegar. This will create the bubbling “volcano effect” that kids love to watch so invite them in on this cleaning project. After allowing your mixture to sit for about 5 minutes, run hot water down the disposal until everything is thoroughly rinsed.
Wrap plumbing tape around the threads of the sink drain where the disposal crews to the sink and the drain threads on the side of the disposal for the drain pipe. Screw the disposal back in under the sink. Screw the drain pipe back to the disposal. Tighten with the pipe wrench. Turn on the water to check for leaks and plug the disposal back in. Turn on the power switch to make sure disposal is running properly.
When well-intentioned citizens confront unaccountable officials, their activities can become more political. I interviewed a municipal civic group leader from St. Petersburg who works on urban ecology and waste. He commented that it has become clear that government officials are responsive not to citizens, but to those “from above” who put them in their offices.
Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
This thing is exactly as everyone else has described. I, like many others, replaced an old ISE Badger with this unit, and it's heads and shoulders above in quality, function, quietness, etc. It grinds everything in seconds (as opposed to batting it around in the chamber for multiple cycles like the Badger). The original plumbing from the Badger lined right up and worked the first time. I'm very pleased with this item... although, there is one thing that I want to note; I read somewhere that if you use the EZ mount system that comes with it, you won't need plumber's putty - one can just use the gasket. This is true ONLY if using a flat lipped SS sink, and even then the rubber seal is optional as opposed to the putty (you can use only one, the putty or the seal with a SS sink, but not both). It's better said that you WILL need plumber's putty, and if you have a stainless steel sink, you have the option to use the thin rubber gasket (I'd use plumber's putty). Other than that minor detail (which made me take an unexpected run to our local hardware store), this unit is great. The one last thing I will say is around quietness. I've read some reviews that talk about how quiet or not quiet it is. I don't understand the desire to have an ultra-quiet garbage disposal. I mean, one needs to run water while the run the disposal, and a full-blast of the faucet going into a spinning basket creates a notable level of sound anyway, plus I want to be able to hear the load of the disposal so I can know when it's clear. This unit is by no means noisy, but I just don't see the desire to go ultra-quiet. Again, this big-boy Waste King is awesome.
In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
Flip the disposer over and unscrew the electrical cover plate on the bottom of the disposer by removing the cover plate screw. Again, be sure the power to the unit has been turned off at the electrical supply panel. Then disconnect the electrical cable connector. Pull out the wires and remove the wire nuts. Also unscrew the ground wire from the green ground screw. Be sure to save the electrical cable connector so you can use it again.
I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.
If your garbage disposal is not running, first check to see if it is plugged in and receiving power. If so then check to see whether it will turn freely with your service wrench. Most disposers are sent with a self service wrench. The wrench is silver and should be located on or near your garbage disposal. (Check under your sink!) If it will not turn freely using the wrench, the disposal is most likely jammed. Check to see if the reset button has popped out.
Fixing a leaky sink flange may be very easy. It could be a simple matter of tightening the bolts that hold the flange onto the sink drain. But if that doesn’t work, you may need to apply a new layer of plumbers putty to seal the flange into place. To do this, you’ll need to loosen the mounting bolts and create enough space between the flange and drain to smear a fresh dab of putty all the way around the drain. Then just re-tighten the bolts and wait a few hours for the putty to form a tight seal.

Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.

Garbage Disposal Repair

×