AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control
Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.

Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]


Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.
I believe if you always run your water first, turn on disposer, then discard food waste down disposer, you will get more longevity from your disposer and less likely have drain stoppage problems. It's also a good practice to run plenty of water (maybe even cleanser) after using the disposer to rinse out the small chamber between the blades and drain pipe. I've found that some disposer stoppages are caused by this chamber being clogged which also causes it to rust and deteriorate prematurely.

As the #1 faucet brand in North America, Moen offers a diverse selection of thoughtfully designed kitchen and bath faucets, showerheads, accessories, bath safety products, garbage disposals and kitchen sinks for residential and commercial applications each delivering the best possible combination of meaningful innovation, useful features, and lasting value.
However, whether the "high Camorra" was an integral part of the Camorra proper is disputed.[16] Although the inquiry did not prove specific collusion between the Camorra and politics, it brought to light the patronage mechanisms that fueled corruption in the municipality.[15] The society's influence was weakened which was exemplified by the defeat of all of their candidates in the 1901 Naples election. Many camorristi left for the United States in the early 20th century.[19]
An affordable option that offers outstanding value, the Waste King Legend Series comes backed by a solid five-year warranty. The stainless steel disposal is compact enough to install under most sinks. The continuous feed design means this disposal requires just a flip of a switch. It runs very quietly, but it is still powerful enough to grind food waste efficiently.
Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services.  If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.
Connect the connector pipe to the elbow and the adjacent sink. Use the connector pipe to connect the elbow piece to the T-fitting on the adjacent sink. The connector piece might need to be cut down to the correct length depending on your sink. Use the nuts and washers provided with your pipes to secure the pieces together using the tongue-and-groove pliers.[1]

But there is really only one rule you need to follow: Never put your hand or fingers down into the disposal, even if you think the disposal has been unplugged or its circuit has been shut off. If a disposal gets turned on accidentally while your fingers are in the opening, the likelihood is that you will end up with bruised fingers, not bloody amputation. But this is not a risk that is necessary in any way.
Wrap plumbing tape around the threads of the sink drain where the disposal crews to the sink and the drain threads on the side of the disposal for the drain pipe. Screw the disposal back in under the sink. Screw the drain pipe back to the disposal. Tighten with the pipe wrench. Turn on the water to check for leaks and plug the disposal back in. Turn on the power switch to make sure disposal is running properly.
The horror movie image of victims having hands and arms severed in a garbage disposal is entirely a Hollywood invention. In reality, the blades inside a garbage disposal are rather dull grinders, not gleaming, razor-sharp sabers. That is not to say that a disposal should be taken lightly—it is indeed possible to be painfully injured if you don't practice basic safety measures. 
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.
The Camorra first emerged during the chaotic power vacuum in the years between 1799 and 1815, when the Parthenopean Republic was proclaimed on the wave of the French Revolution and the Bourbon Restoration. The first official mention of the Camorra as an organization dates from 1820, when police records detail a disciplinary meeting of the Camorra, a tribunal known as the Gran Mamma. That year a first written statute, the frieno, was also discovered, indicating a stable organisational structure in the underworld. Another statute was discovered in 1842, including initiation rites and funds set aside for the families of those imprisoned. The organization was also known as the Bella Società Riformata, Società dell'Umirtà or Onorata Società.[9][10]
From the rich industrialist who wants a clear road into politics or administration to the small shopowner who wants to ask for a reduction of taxes; from the businessman trying to win a contract to a worker looking for a job in a factory; from a professional who wants more clients or greater recognition to somebody looking for an office job; from somebody from the provinces who has come to Naples to buy some goods to somebody who wants to emigrate to America; they all find somebody stepping into their path, and nearly all made use of them.[18]
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
Whether you repaired or replaced the leaking garbage disposal, test for any missed problem spots. Wipe the unit dry with a clean cloth, then unplug the sink drain (if plugged) and pour a few cups of dyed water into the drain once more. Use a flashlight to inspect the entire unit. If you don’t observe a leak, turn on the power to the disposal from your breaker box and plug in the disposal at the wall outlet.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.

The only existing hole I can think of ‘near the top’ that is a part of the unit, would be the place where a dishwasher hose would attach. Was that disposal once connected to a dishwasher that is no longer there? If so, that could be why water is coming out of ‘an existing hole’… Seems silly maybe, but sometimes the most obvious really is the answer.
Jarred Connections: Considering the garbage-disposal systems is located under the kitchen sink, and since the area under the kitchen sink is a common place for storing all sorts of things, it is fairly common for the unit to get bumped.If it gets hit hard enough, the unit can actually shift so that it is no longer sitting straight. Pipes can also get knocked around, causing the seals to lose effectiveness.
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.

After using the lowest cost disposers for over 20 years now, I find the newest models have not withstood regular use for more than 5 years. The older models had a blue housing where this next step-up model has a black housing which I am hoping for at least 5 years use. Our oldest (blue housing) disposers have lasted at least 5 years and some are now almost 20 years old.


Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]
Single Stream Recycling: Cedar Park was one of the first communities in central Texas to offer residents single-stream recycling. We began providing this service in February 2010. This has been incredibly successful; our average monthly recycling has jumped from 98 tons (when residents used the small blue bin) of diverted waste to 252 tons (now that residents have access to the larger 90 gallon bin)! 

With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes ... full review


If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
The bulk of a food waste disposer system, which includes the seals and pipes, is located beneath the kitchen sink. Most homeowners use this space to store various items, and it is not uncommon for people to bump or jar the disposal’s pipes when reaching for an item that is in close proximity. If the pipes are struck hard enough, the pipes can shift so that they are no longer sitting properly. Retaining bolts can become loose. Pipes may move, and seals can shift into an awkward position.

Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.
When well-intentioned citizens confront unaccountable officials, their activities can become more political. I interviewed a municipal civic group leader from St. Petersburg who works on urban ecology and waste. He commented that it has become clear that government officials are responsive not to citizens, but to those “from above” who put them in their offices.
Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
If you're replacing a commercial garbage disposal, then you'll either want the Drain Strainer with Crown Adapter or the Drain Strainer XL. Both of these models have a universal Crown Adapter on top that serves as a funnel to cover the hole once the commercial garbage disposal has been removed. Note that it doesn't actually attach to the sink bowl, but you'll adjust the legs to get your unit flush underneath the bottom of the sink.
Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).
Saviano alleges that from the 1980s, Italian gangsters ran a network of lucrative businesses in the city as well as many illegal rackets. Saviano said Scotland's third city, with no history of organized crime, was seen as an attractive safe haven away from the violent inter-gang bloodletting that had engulfed their Neapolitan stronghold of Mondragone. Saviano claims that before the Italian clans arrived, Aberdeen did not know how to exploit its resources for recreation and tourism. He further states that the Italians infused the city with economic energy, revitalised the tourist industry, inspired new import-export activities and injected new vigour in the real-estate sector. It thereby turned Aberdeen into a chic, elegant address for fine dining and important dealings.[55]
3/4th Horsepower – This garbage disposal model is ideal for households of 4-5 people. It is the model that you will most commonly find in modern day homes. These models are often equipped with more sound dampening features, which reduce the level of noise the unit produces when compared to its lower end cousins. Again, it is recommended that you look for a model with stainless steel grinding components.
I've always had Insinkerator garbage disposals so I just didn't know any better but now I do. Simply put, this is truly the king of garbage disposals. The amount of power it has is ridiculous and it will tear through just about any food I've thrown at it. Now, I have been hesitant to test it with some tougher items (I've heard stories of people feeding it chicken and rib bones) because I was always taught to be careful what you put down the disposal (a cheap wimpy unit in a relative's shore house seizes up with unpopped corn kernels and their home unit clogged with shredded zucchini). I have given it some things like apple cores though with absolutely no problem. I never would have put an apple core down my old Insinkerator. This king eats the core in about 3-5 seconds, if that. Completely gone. The thing that absolutely astounds me about this unit though is how QUIET it is. It's almost ridiculous. My old one, and most everyone else's I've ever heard sounds like an electric chain saw. This one sounds like someone is humming. When people come over I run it form them just to show off how quiet it is. I know. I'm weird. Add to that a lifetime warranty and this thing just cannot be beat for the money. Google it yourself and you will see how many people agree that this is the best value disposal available. The cheap Insinkerators will normally run you about $80. It's not that much more to get one of these and the benefits for the small price increase are totally worth it. For 50% more you get way more than a 50% better disposal. Of course you could spend $350 on the Insinkerator Elite but is that one going to be 300% better. I doubt it. If you found this review helpful please click yes below.
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.

After using the lowest cost disposers for over 20 years now, I find the newest models have not withstood regular use for more than 5 years. The older models had a blue housing where this next step-up model has a black housing which I am hoping for at least 5 years use. Our oldest (blue housing) disposers have lasted at least 5 years and some are now almost 20 years old.
Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
When rubber gaskets age, they can develop leaks. The gasket can dry up, crack, and leak when it is repeatedly exposed to long periods of disuse where no water is present in the drain pipe. Should an older garbage disposal be removed and then placed back, it will require a new rubber gasket to again achieve a watertight seal. Moreover, if a gasket is not evenly locked on all three sides, then it will develop a leak.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
×