Installing a garbage disposal involves tapping into your home’s plumbing and electrical systems, and both systems need to be handled correctly to safely install your garbage disposal. Someone with a lot of experience can handle the job in 2 or 3 hours—or maybe even less. Attempting a garbage disposal installation without any training will likely take at least double the time required for a professional to install the garbage disposal.
Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
Garbage protests in Volokolamsk and elsewhere have exposed weaknesses in Russia’s system of political authority, often described as a “power vertical” in which government officials answer not to their constituents, but to their political superiors and ultimately to President Putin. Facing unresponsive or incompetent officials, citizens turn to Putin as the only one who can solve their problems.
Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
Fixing a leaky sink flange may be very easy. It could be a simple matter of tightening the bolts that hold the flange onto the sink drain. But if that doesn’t work, you may need to apply a new layer of plumbers putty to seal the flange into place. To do this, you’ll need to loosen the mounting bolts and create enough space between the flange and drain to smear a fresh dab of putty all the way around the drain. Then just re-tighten the bolts and wait a few hours for the putty to form a tight seal.
If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.
If there is nothing visible clogging your disposal unit, the flip switch on your garbage disposal unit may have turned the unit off. This little red switch is located underneath your unit and protects against overheating and arcing situations. You can try pushing the red switch to reset the garbage disposal unit. Test your unit by turning it on. If it still won't turn on or makes a humming noise, unplug the unit or turn it off at the breaker box, and move to step 4.

If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.


Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.
AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control
A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close

Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.


With the assistance of private businessmen known as "stakeholders", the numerous Camorra clans are able to gain massive profits from under-the-table contracts with local, legitimate businesses. These "stakeholders" are able to offer companies highly lucrative deals to remove their waste at a significantly lower price. With little to no overhead, Camorra clans and their associates see very high profit margins. According to author Roberto Saviano, the Camorra uses child labour to drive the waste in for a small price, as they do not complain about the health risks as the older truckers might.
Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]
The large-capacity disposer chamber boasted by this GE The large-capacity disposer chamber boasted by this GE 1/3 HP Continuous-Feed Garbage Disposal features a cold-rolled carbon steel armature shaft and dishwasher drain connector. It also has a stainless-steel sink flange ensuring durability and providing ample space for waste disposal. The disposer harnesses the power of jam-resistant dual stainless-steel swivel ...  More + Product Details Close
Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.

STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!
To reseal the leaky flange, you must first detach the garbage disposal. Start by loosening the screws securing the main drain pipe to the disposal, then loosen the screws in the metal clamp securing the dishwasher hose to the disposal and detach the drain pipe and dishwasher hose from the disposal. Loosen the screws in the mounting ring that connects the disposal to the metal mounting assembly beneath the sink, then pull down the disposal and carefully set it on a clean, dry surface. Loosen the bolts in the mounting assembly with a wrench, then pull down the mounting assembly and set it near the disposal.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
Fixing a leaky sink flange may be very easy. It could be a simple matter of tightening the bolts that hold the flange onto the sink drain. But if that doesn’t work, you may need to apply a new layer of plumbers putty to seal the flange into place. To do this, you’ll need to loosen the mounting bolts and create enough space between the flange and drain to smear a fresh dab of putty all the way around the drain. Then just re-tighten the bolts and wait a few hours for the putty to form a tight seal.
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.
If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
Even the most trustworthy garbage disposal will develop a leak from time to time; however, just because your food waste disposer has developed a leak does not necessarily mean that it needs to be replaced. Doing a little bit of investigating and troubleshooting before deciding to run out and buy a new garbage disposal can mean the difference between spending $10.00 for a replacement and $100.00+ to replace the entire unit.
The InSinkErator Badger 1 Continuous Feed Garbage Disposal 1/3 HP features a quick-mounting system that allows for easy installation or replacement. This sturdy garbage Disposal is constructed from galvanized steel and features a 26 oz. chamber for space-saving waste disposal. The garbage Disposal also features a 1/3 HP motor that rapidly grinds food waste for easy rinsing down the drain.

Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services.  If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.
Your garbage disposer is not draining, has water leaks, creates weird noises, or has horrible odors? Troubleshoot your Faulty Disposer. If you are experiencing garbage disposal problems, you will find solutions on our checklist below to help you repair it. Before going out and spending a few hundred dollars on a new one, troubleshoot your existing sink garbage disposer to find the problem.
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.

FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.

Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
The easiest way to apply that force is to squeeze them together using tongue-and-groove pliers, such as Channellocks. You’ll need medium or large pliers to do this. Unlike prying on the lower ring with a screwdriver or hex wrench-the method recommended in most instruction sheets-squeezing can’t disturb the position of the sink flange and cause it to leak. Plus, it’s easier on the wrists.
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]
×