Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
Single Stream Recycling: Cedar Park was one of the first communities in central Texas to offer residents single-stream recycling. We began providing this service in February 2010. This has been incredibly successful; our average monthly recycling has jumped from 98 tons (when residents used the small blue bin) of diverted waste to 252 tons (now that residents have access to the larger 90 gallon bin)!
The horror movie image of victims having hands and arms severed in a garbage disposal is entirely a Hollywood invention. In reality, the blades inside a garbage disposal are rather dull grinders, not gleaming, razor-sharp sabers. That is not to say that a disposal should be taken lightly—it is indeed possible to be painfully injured if you don't practice basic safety measures.
Your garbage disposer is not draining, has water leaks, creates weird noises, or has horrible odors? Troubleshoot your Faulty Disposer. If you are experiencing garbage disposal problems, you will find solutions on our checklist below to help you repair it. Before going out and spending a few hundred dollars on a new one, troubleshoot your existing sink garbage disposer to find the problem.
This is a heavy-duty stopper that does the job well for my light use in the kitchen. The only remark I'll make is that I always lift out garbage disposal stoppers and strainers after each use and keep them inverted with the concave side down over the drain so they dry out completely. The stopper isn't doing anything for you in between uses, so there's no sense in keeping it seated tightly in the drain. Keep it inverted and dried out to prevent disgusting scum from accumulating rapidly.
If you’re unsuccessful using the wrench, you may need to go in through the drain in an attempt to remove the clog. Disconnect the power to the disposal by unplugging the unit or turning off its circuit breaker, then use long-handled tongs and a flashlight to try to remove the jam. Never use your hands for this task, even if the disposal is completely disconnected from its power source! Fumbling blindly around a disc of sharp blades is asking for injury.
Garbage disposals can range from $70 on the low end to $380 on the high end -- and generally speaking, you get what you pay for. A less expensive unit is likely to produce more noise, require more water, and clog more easily than a higher-end model. Likewise, a more expensive unit will be faster, quieter and less likely to malfunction than a lower end model -- and it will be lighter-weight and offer greater capacity as well. The average cost of a garbage disposal installation with a one-year manufacturer’'s warranty is $185. The average amount of time taken to install a garbage disposal, including cleanup, is three hours. The hourly cost for labor will range from $20 to $40 -- $28 on average.
To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.