I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.
If you have a broken seal on the inside of your garbage disposal, you will see leaking coming from the bottom of your unit. Leaks that come from the bottom of your garbage disposal are usually attributed to cracks on the inside of the device. This is due to basic wear and tear overtime. To fix this issue, you’ll need simply invest in a new garbage disposal.
As I have mentioned, garbage disposers for most people are just another kitchen appliance that we tend to take for granted, and this is one of the reasons I decided to bring this website to the internet. I have come across many customers over the years that only seem to notice this “gadget” when it goes wrong, and believe it or not, most of the time they go wrong is because they’re not cared for properly.
Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
Thank you for sharing this tutorial. My husband and I tried to fix our garbage disposal last week but we couldn’t get it to work. When we turn it on, it makes a humming noise, but nothing is blocking the blades. We might need to get a new disposal, but we’ll probably have a professional look at it before we decide. We’ll keep your tips on hand, just in case.
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
The large-capacity disposer chamber boasted by this GE The large-capacity disposer chamber boasted by this GE 1/3 HP Continuous-Feed Garbage Disposal features a cold-rolled carbon steel armature shaft and dishwasher drain connector. It also has a stainless-steel sink flange ensuring durability and providing ample space for waste disposal. The disposer harnesses the power of jam-resistant dual stainless-steel swivel ...  More + Product Details Close
Many localities in the United States prohibited the use of disposers.[8] For many years, garbage disposers were illegal in New York City because of a perceived threat of damage to the city's sewer system. After a 21-month study with the NYC Department of Environmental Protection,[9] the ban was rescinded in 1997 by local law 1997/071, which amended section 24-518.1, NYC Administrative Code.[10]
STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!
Garbage disposals first appeared in households in the 1930's and 1940's. These appliances, which are installed under a kitchen sink, can make a cook's life easier by trapping and shredding food waste items, allowing it to pass through the plumbing system. Although these popular appliances make cooking and cleaning much more convenient, they do require regular maintenance to keep them running at optimal performance. When it is time to replace your garbage disposal's blades, you can save time and money by doing it yourself.
This thing is exactly as everyone else has described. I, like many others, replaced an old ISE Badger with this unit, and it's heads and shoulders above in quality, function, quietness, etc. It grinds everything in seconds (as opposed to batting it around in the chamber for multiple cycles like the Badger). The original plumbing from the Badger lined right up and worked the first time. I'm very pleased with this item... although, there is one thing that I want to note; I read somewhere that if you use the EZ mount system that comes with it, you won't need plumber's putty - one can just use the gasket. This is true ONLY if using a flat lipped SS sink, and even then the rubber seal is optional as opposed to the putty (you can use only one, the putty or the seal with a SS sink, but not both). It's better said that you WILL need plumber's putty, and if you have a stainless steel sink, you have the option to use the thin rubber gasket (I'd use plumber's putty). Other than that minor detail (which made me take an unexpected run to our local hardware store), this unit is great. The one last thing I will say is around quietness. I've read some reviews that talk about how quiet or not quiet it is. I don't understand the desire to have an ultra-quiet garbage disposal. I mean, one needs to run water while the run the disposal, and a full-blast of the faucet going into a spinning basket creates a notable level of sound anyway, plus I want to be able to hear the load of the disposal so I can know when it's clear. This unit is by no means noisy, but I just don't see the desire to go ultra-quiet. Again, this big-boy Waste King is awesome.
I believe if you always run your water first, turn on disposer, then discard food waste down disposer, you will get more longevity from your disposer and less likely have drain stoppage problems. It's also a good practice to run plenty of water (maybe even cleanser) after using the disposer to rinse out the small chamber between the blades and drain pipe. I've found that some disposer stoppages are caused by this chamber being clogged which also causes it to rust and deteriorate prematurely.
Whether you repaired or replaced the leaking garbage disposal, test for any missed problem spots. Wipe the unit dry with a clean cloth, then unplug the sink drain (if plugged) and pour a few cups of dyed water into the drain once more. Use a flashlight to inspect the entire unit. If you don’t observe a leak, turn on the power to the disposal from your breaker box and plug in the disposal at the wall outlet.
Unlike the Sicilian Mafia, which has a clear hierarchy and a division of interests, the Camorra's activities are much less centralized. This makes the organization much more difficult to combat through crude repression.[39] In Campania, where unemployment is high and opportunities are limited, the Camorra has become an integral part of the fabric of society. It offers a sense of community and provides the youth with jobs. Members are guided in the pursuit of criminal activities, including cigarette smuggling, drug trafficking, and theft.[40]
Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.
If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
Despite the overwhelming magnitude of the problem, law enforcement officials continue their pursuit. The Italian police are coordinating their efforts with Europol at the European level as well as Interpol to conduct special operations against the Camorra. The Carabinieri and the Financial Police (Guardia di Finanza) are also fighting criminal activities related to tax evasion, border controls, and money laundering. Prefect Gennaro Monaco, Deputy Chief of Police and Chief of the Section of Criminal Police cites "impressive results" against the Camorra in recent years, yet the Camorra continues to grow in power.[42]
As it's a direct replacement, I didn't even bother to go through the hassle or removing the old sink flange and having to putty in a new one as the existing one was just fine. It took me about 5 minutes to replace old with new - that's why I didn't bother with a different make. I'm an average Joe who does a few things around the house - mostly accompanied by a lot of cussing - so anything that makes such work quick and simple results in less swearing - which is a good thing right?!
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.

Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.


Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.

Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.

Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
GE, which is an acronym for General Electric, is an international conglomerate whose headquarters are based in New York City, New York. The company operates in many different segments, ranging from home appliances to transportation. In terms of gross revenue, GE is the sixth largest company firm in the United States. GE garbage disposals have won praise for their powerful motors and overall durability.

I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?

As advertised, it does come with a corded plug so it will need an outlet. My old Badger was a direct wire. Some folks tore out the cord and the strain relief as a fix and hard wired it like their old one. Some folks put an outlet in, which I found that to be a 15 minute job. I didn't want to mess around with chopping out the stock cord and putting in a new one and messing with the strain relief replacement. I thought the new outlet process was much easier because, heck, the wire's already there and that's always the hardest part of wiring a box! I shoved some of the extra length of the existing wire back into the hole in the wall that it came out from. I thought carefully about where the new box should go so the body of the disposal didn't hit it. I screwed it to the back of the cabinet, poked the wires into the box, screwed them to a new receptacle and, voila!. NOTE: IF YOU DON'T KNOW WHAT YOU'RE DOING WITH ELECTRICAL WIRING, DO NOT ATTEMPT THIS YOURSELF. If you do, be sure to kill the power at the circuit breaker and it is probably the easiest box you will install. Just make sure it is securely mounted into something besides the flimsy back panel of the cabinet.
The bulk of a food waste disposer system, which includes the seals and pipes, is located beneath the kitchen sink. Most homeowners use this space to store various items, and it is not uncommon for people to bump or jar the disposal’s pipes when reaching for an item that is in close proximity. If the pipes are struck hard enough, the pipes can shift so that they are no longer sitting properly. Retaining bolts can become loose. Pipes may move, and seals can shift into an awkward position.
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
The only existing hole I can think of ‘near the top’ that is a part of the unit, would be the place where a dishwasher hose would attach. Was that disposal once connected to a dishwasher that is no longer there? If so, that could be why water is coming out of ‘an existing hole’… Seems silly maybe, but sometimes the most obvious really is the answer.
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close
If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.
Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.
Badger food waste disposers are a reliable and Badger food waste disposers are a reliable and functional choice when affordability is the prime concern. Badger 5XP features a 3/4 horsepower heavy-duty quiet Dura-Drive induction motor rugged galvanized steel construction for disposer durability and a space-saving compact design. To top it off Badger 5XP offers a 3-year We Come ...  More + Product Details Close
×