Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.

If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
The government has made an effort to combat the Camorra's criminal activities in Campania. The solution ultimately lies in Italy's ability to offer values, education and work opportunities to the next generation. However, the government has been hard pressed to find funds for promoting long term reforms that are needed to improve the local economic outlook and create jobs.[40] Instead, it has had to rely on limited law enforcement activity in an environment which has a long history of criminal tolerance and acceptance, and is governed by a code of silence or omertà that persists to this day.[41]
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.

See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.

I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
This is a heavy-duty stopper that does the job well for my light use in the kitchen. The only remark I'll make is that I always lift out garbage disposal stoppers and strainers after each use and keep them inverted with the concave side down over the drain so they dry out completely. The stopper isn't doing anything for you in between uses, so there's no sense in keeping it seated tightly in the drain. Keep it inverted and dried out to prevent disgusting scum from accumulating rapidly.
Why am I writing a review about my beloved garbage disposal? Why am I referring to it as my "beloved" garbage disposal? I replaced a different garbage disposal from Costco; it had lasted a few years before giving up the ghost (the metal teeth within had basically corroded and broken off). Even before it met its untimely end, it had been loud and took a long time to grind things up--despite it being 1-1/4 horsepower!
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
Badger food waste disposers are a reliable and Badger food waste disposers are a reliable and functional choice when affordability is the prime concern. Badger 5XP features a 3/4 horsepower heavy-duty quiet Dura-Drive induction motor rugged galvanized steel construction for disposer durability and a space-saving compact design. To top it off Badger 5XP offers a 3-year We Come ...  More + Product Details Close
×