After you install the new sink flange, you don’t want it shifting around when you’re assembling the parts underneath. Movement of the flange could break the seal between the flange and the sink, inviting a leak. Your best bet is to ask a helper to press down on the sink flange, or if you’re working alone, find something to weigh it down, such as the old disposal. Place an old towel under the weight so you don’t scratch the sink. If the bottom of your sink is quite concave, the old disposal might not contact the flange. In that case, place a can on the flange, then weigh down the can.
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.
Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.
Single Stream Recycling: Cedar Park was one of the first communities in central Texas to offer residents single-stream recycling. We began providing this service in February 2010. This has been incredibly successful; our average monthly recycling has jumped from 98 tons (when residents used the small blue bin) of diverted waste to 252 tons (now that residents have access to the larger 90 gallon bin)! 
Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).
The garbage disposal in your kitchen sink is a convenient way to get rid of scraps and leftovers, but when a foreign object like a glass gets caught in it, it can jam the mechanism and stop it from working. Removing a glass from a garbage disposal involves removing any large pieces of glass; dislodging the glass by inserting a wrench or broom handle into the bottom or top of the disposal; vacuuming the disposal; resetting it; or if none of the other steps work, removing the disposal and shaking out all of the glass. Read the following steps to find out how to remove a glass from a garbage disposal.
To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
Compared to the Sicilian Mafia's pyramidal structure, the Camorra has more of a 'horizontal' than a 'vertical' structure. As a result, individual Camorra clans act independently of each other, and are more prone to feuding among themselves. This however makes the Camorra more resilient when top leaders are arrested or killed, with new clans and organizations germinating out of the stumps of old ones. As the Galasso clan boss Pasquale Galasso once stated in court; "Campania can get worse because you could cut into a Camorra group, but another ten could emerge from it."[27]
Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.
As advertised, it does come with a corded plug so it will need an outlet. My old Badger was a direct wire. Some folks tore out the cord and the strain relief as a fix and hard wired it like their old one. Some folks put an outlet in, which I found that to be a 15 minute job. I didn't want to mess around with chopping out the stock cord and putting in a new one and messing with the strain relief replacement. I thought the new outlet process was much easier because, heck, the wire's already there and that's always the hardest part of wiring a box! I shoved some of the extra length of the existing wire back into the hole in the wall that it came out from. I thought carefully about where the new box should go so the body of the disposal didn't hit it. I screwed it to the back of the cabinet, poked the wires into the box, screwed them to a new receptacle and, voila!. NOTE: IF YOU DON'T KNOW WHAT YOU'RE DOING WITH ELECTRICAL WIRING, DO NOT ATTEMPT THIS YOURSELF. If you do, be sure to kill the power at the circuit breaker and it is probably the easiest box you will install. Just make sure it is securely mounted into something besides the flimsy back panel of the cabinet.

Locate the circuit breaker that controls power to the garbage disposal, and flip it to the "off" position before continuing. Fix or replace the main seal if it is leaking. Remove both the drain pipe and the dishwasher hose, if applicable. Insert a screwdriver into the tightening ring and turn it counterclockwise. This will release the garbage disposal unit. Inspect the main seal that sits on the top of the unit. The seal is a large, soft rubber fitting that covers the top edge of the garbage disposal. If dirt, grit or food particles have fouled the main seal, wipe it down with a damp rag and reinstall the disposal unit. If the main seal is cracked, pitted or broken, it needs to be replaced. Once a new main seal has been inserted into the garbage disposal, push it up against the mounting bracket, insert a screwdriver into the tightening ring, and turn it clockwise to lock the unit into place. Reinstall the drain pipe and dishwasher hose, if applicable.
Assuming that you have already given the disposal the time it needs to run and clear the garbage, you probably have a congested drain line. We don’t recommend using chemical drain cleaners with a garbage disposal. You will very likely just damage the unit and end up with a sink full of toxic chemicals that you’ll eventually be forced to clean out manually. If the blockage doesn’t go down with the good ol’ baking soda and vinegar remedy, then calling a John Moore professional is your best bet. He or she will know exactly how to properly remove the bolts, disconnect the drain trap and remove the trap and the discharge drain pipe, check for clogs and any other obstructions, and finally clear the blockage with the latest and best tools. (See our previous post about good steps you can take when your kitchen sink is clogged!)
The Camorra received another blow with the Cuocolo trial (1911–1912). While the trial was about the murder of the Camorrista Gennaro Cuocolo and his wife, suspected of being police spies, on June 6, 1906, the main investigator, Carabinieri Captain Carlo Fabbroni, transformed it from a murder trial into one against the Camorra as a whole. Fabbroni intended to use the trial to strike the final blow to the Camorra.[20][21] The trial attracted a lot of attention of newspapers and the general public both in Italy as well as in the United States, including by Pathé's Gazette.[22] The hearings began in the spring of 1911 and would continue for twelve months. After a 17-month trial, the often tumultuous proceedings ended with a guilty verdict on July 8, 1912. The defendants, including 27 leading Camorra bosses, were sentenced to a total of 354 years' imprisonment. The main defendant and nominal head of the Camorra, Enrico Alfano, was sentenced to 30 years.[20][23][24][25]
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
The origins of the Camorra are not entirely clear. It may date back to the 17th century as a direct Italian descendant of a Spanish secret society, the Garduña, founded in 1417. Officials of the Kingdom of Naples may have introduced the organization to the area, or it may have grown gradually out of small criminal gangs operating in Neapolitan society near the end of the 18th century.[3] However, recent historical research in Spain suggests that the Garduña never really existed and was based on a fictional 19th century book.[4]
Manufactured in the United States, Waste King garbage disposals have won much praise for their energy efficient design. Waste King offers a wide range of garbage disposers for both residential and commercial settings. In the early 2000s, Waste King refocused their sights on providing unparalleled customer service and quality products, and their warranties are the current industry standard that others are measured by.
Loosen the nut securing the rest of the assembly. Just below the sink flange where the drain empties into the garbage disposal you’ll see a circular plastic piece similar in appearance to the mounting ring. Insert the tip of a screwdriver into one of the lugs on this piece and rotate it in a counterclockwise direction. Pull the nut away and set it aside.[9]
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.

In the 1970s and 1980s Raffaele Cutolo made an attempt to unify the Camorra families in the manner of the Sicilian Mafia, by forming the New Organized Camorra (Nuova Camorra Organizzata or NCO), but this proved unsuccessful. Drive-by shootings by camorristi often result in casualties among the local population, but such episodes are often difficult to investigate because of widespread omertà (code of silence). According to a report from Confesercenti, the second-largest Italian Trade Organization, published on October 22, 2007 in the Corriere della Sera, the Camorra control the milk and fish industries, the coffee trade, and over 2,500 bakeries in Naples.[28]

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.

Garbage Disposal Repair

×