If you can hear your disposal’s motor humming, but the disposal won’t grind, sounds loud, or starts and stops, it’s probably because something jammed it. Disposals jam when something gets lodged in the “flywheel,” which is what the disposal’s rotating plate is called. You can fix it yourself, but remember: NEVER stick your hand down the garbage disposal. Ever. Seriously.
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.
Warranty - The average industry warranty on a garbage disposal is one year; however, it is not uncommon to see manufacturers’ warranties that can extend up to ten years. As a general rule of thumb, the more comprehensive and longer a warranty is, the more confidence the manufacturer has in the product they have made, but this is not always the case, so it is still important to do your homework.
Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.
Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control
I'm not what you'd call a handyman, although I've been working to get better at that. I will now at least try a home project before passing on it. So, when our 15-year garbage disposal died I had another opportunity. I determined our old unit to be a Badger 5 1/2 HP (this exact item). I didn't have time to wait for the item to arrive from Amazon so I went to Home Depot and coughed up an extra $20 for the Badger 500 - Home Depot's branded version of this item. They are identical except for the name & sticker.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.
Personally I'd recommend if you have a disposal have it removed. Most people don't realize, there is very little you are supposed to put in them. Whereas, they are the primary reason for your kitchen sink drain getting clogged. Just use the trash, it could save you an expensive Drain cleaning bill. Here's a tip for y'all who do have them. After use let warm water run while it's still running for 3 to 4 minutes, that will help push everything to the bigger main drain .

STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.


Dishwasher Connection: Some disposals are connected to the dishwasher drain pipe, which drains leftover food removed from dishes going through the wash cycle. Leaks can sometimes occur in the hose connections where the disposal hose attaches to the dishwasher.Leaks can also happen if the seal on the hose is compromised or the clamp on the hose isn’t tight enough. If the connecting hose seems to be the source of the leak, try tightening the connection or replacing the seal. If neither solutions work, or the hose is obviously cracked, you will need to replace the hose.

I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
In 1977, brothers Bob and Jim Gregory founded Texas Disposal Systems, Inc. with $10,000, one customer, one truck and plenty of determination. Building on a deep commitment to customer satisfaction and environmental preservation, the Gregory Family created a collection of businesses that has become one of the largest independently-owned solid waste collection and disposal companies in central Texas.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.

One last thought - Beef bones? I see that Consumer Reports tests these things by measuring the fineness of the grind using beef bones. Do people really put beef bones down a garbage disposal on purpose? You might think I'm babying mine, or maybe that's why I didn't have excessive vibration when I use it, but I'll put the beef bones in the trash and grind up the rest of the stuff with this and be just fine for many years to come, I hope!


Garbage disposals help us get rid of food waste, so it’s not surprising that the appliance may be susceptible to gross smells. A capful of bleach or grinding up citrus peels can help eliminate any foul odors coming from your garbage disposal. However, if nothing seems to help your appliance in the smell department, it may be catching food particles within its crevices. We recommend disassembling your garbage disposal to clean it, or replacing it if it’s old.
After watching this video, I decided I could replace my garbage disposer myself. Honestly, I think your site completely misrepresents how VERY difficult it is to hold up a 20+ pound disposal unit firmly up against the mounting hardware as you are literally crammed under your kitchen sink and then try and somehow get all three tabs to slide into place. I was very disappointed and, after 4 nights of trying and retrying, finally just called a plumber. Please don’t show anyone lifting something that is big and heavy and make it seems as light as a feather. Shame. Shame.
Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.

The MOEN GX PRO Series of garbage disposals The MOEN GX PRO Series of garbage disposals packs all the standard features and reliable performance into a sleek and compact form ideal for professionals and consumers alike. Installation is simplified with the Universal Xpress Mount which fits on all MOEN and most existing 3-bolt mounting assemblies. Eliminate everyday kitchen ...  More + Product Details Close
×