How many years do garbage disposals last? One the average, quite a long time. In fact, with adequate care and proper maintenance, garbage disposal units can be of good service for about 8 to 15 years. This means the blades remain efficient and the motor has not burned out yet. This being said, neglecting garbage disposal leaks will significantly decrease this effective service life.


Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.

The Camorra first emerged during the chaotic power vacuum in the years between 1799 and 1815, when the Parthenopean Republic was proclaimed on the wave of the French Revolution and the Bourbon Restoration. The first official mention of the Camorra as an organization dates from 1820, when police records detail a disciplinary meeting of the Camorra, a tribunal known as the Gran Mamma. That year a first written statute, the frieno, was also discovered, indicating a stable organisational structure in the underworld. Another statute was discovered in 1842, including initiation rites and funds set aside for the families of those imprisoned. The organization was also known as the Bella Società Riformata, Società dell'Umirtà or Onorata Società.[9][10]
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”
Lowe's offers garbage disposals like the InSinkErator Evolution and Badger garbage disposals in various horsepower options. Models with lower horsepower tend to become jammed easily. What if your garbage disposal jams? No problem. Simply locate the hex socket in the center of the underside of the disposal. Grab a hex wrench, put it in the socket, and work it back and forth until you feel the blades loosen up. Once the blades are spinning freely, press the garbage disposal reset button. It's that easy.
Run your garbage disposal for longer each time you use it. A mistake many people make is turning off their garbage disposal as soon as the grinding noises stop. It is better to leave the garbage disposal on (with the water running) for several seconds after the grinding noises subside, as there may still be small particles in the disposal unit which have not yet been cleared away.
Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.

Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.


In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
The original low camorra held sway over the poor plebs in an age of abjection and servitude. Then there arose a high camorra comprising the most cunning and audacious members of the middle class. They fed off trade and public works contracts, political meetings and government bureaucracy. This high camorra strikes deals and does business with the low camorra, swapping promises for favours and favours for promises. The high camorra thinks of the state bureaucracy as being like a field it has to harvest and exploit. Its tools are cunning, nerve and violence. Its strength comes from the streets. And it is rightly considered to be more dangerous, because it has re-established the worst form of depotism by founding a regime based on bullying. The high camorra has replaced free will with impositions, it has nullified individuality and liberty, and it has defrauded the law and public trust.[15][16]
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.
Garbage disposals can range from $70 on the low end to $380 on the high end -- and generally speaking, you get what you pay for. A less expensive unit is likely to produce more noise, require more water, and clog more easily than a higher-end model. Likewise, a more expensive unit will be faster, quieter and less likely to malfunction than a lower end model -- and it will be lighter-weight and offer greater capacity as well. The average cost of a garbage disposal installation with a one-year manufacturer’'s warranty is $185. The average amount of time taken to install a garbage disposal, including cleanup, is three hours. The hourly cost for labor will range from $20 to $40 -- $28 on average.
Why am I writing a review about my beloved garbage disposal? Why am I referring to it as my "beloved" garbage disposal? I replaced a different garbage disposal from Costco; it had lasted a few years before giving up the ghost (the metal teeth within had basically corroded and broken off). Even before it met its untimely end, it had been loud and took a long time to grind things up--despite it being 1-1/4 horsepower!
Knowing the difference between what can go down the disposal and what should go into the trash can save you an emergency call to the plumber. This is especially pertinent during the holidays when the kitchen is filled with people and the sink with dirty dishes. Practice these three everyday maintenance tips to help you maximize the lifespan of your garbage disposal.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)
Another method for cleaning and deodorizing your disposal unit is to sprinkle some baking soda in your unit and rinse it with about a cup of vinegar. This will create the bubbling “volcano effect” that kids love to watch so invite them in on this cleaning project. After allowing your mixture to sit for about 5 minutes, run hot water down the disposal until everything is thoroughly rinsed.
Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
Inspect each of these locations while gliding a light-colored rag over the unit; the dyed water will readily show on the rag and reveal the location of the leak. If a leak isn’t immediately apparent, remove the sink stopper and pour a few more cups of dyed water down the sink drain, then check for leaks again. Leaks near the top of the unit are more likely to show themselves while the sink is plugged, while side and bottom leaks are more noticeable while the sink is unplugged.
3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.

Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.

This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:

Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.

"Thank you for creating a product that will help reduce the need to call a plumber every 2-3 weeks. I have tried various options to get my staff to take better care of what goes down the 3 compartment sink drain but it did not work. The Drain Strainer makes it extremely simple for them. The first two XL's that I ordered have worked perfectly. These additional two I ordered are for a different location and we expect the same results there." Jim Abanto - Owner El Chalan Restaurant - Miami FL
Leaks from the bottom of the garbage disposal (often from the reset button) commonly indicate that at least one seal on the interior shell of the unit that protects the motor has deteriorated, or that the shell itself has cracked. These vulnerabilities can cause water from the sink to seep into the shell of the disposal and leak out of the base of the unit. In an old garbage disposal, one compromised internal seal is often accompanied by others, so your best bet is to install a new one.
The 2 800 RPM motor-powered dual stainless-steel swivel The 2 800 RPM motor-powered dual stainless-steel swivel impellers built into this GE 1/2 HP Continuous-Feed Garbage Disposal join forces with a 2-level pre-cutter to make it easy to grind undesirable waste into easily drainable particles. The disposer's large-capacity disposer chamber is comprised of a cold-rolled carbon steel armature shaft ...  More + Product Details Close
This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!

This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!


After you install the new sink flange, you don’t want it shifting around when you’re assembling the parts underneath. Movement of the flange could break the seal between the flange and the sink, inviting a leak. Your best bet is to ask a helper to press down on the sink flange, or if you’re working alone, find something to weigh it down, such as the old disposal. Place an old towel under the weight so you don’t scratch the sink. If the bottom of your sink is quite concave, the old disposal might not contact the flange. In that case, place a can on the flange, then weigh down the can.
You can buy a 1/3-hp disposal for $80 or less, but our experts suggest that a more expensive unit with at least 3/4 hp would be a better choice. The more powerful the motor, the less chance it will jam. In addition, higher-priced disposals are generally quieter and have longer warranties. If you need to replace the splash guard guard as part of your garbage disposal installation, take a look at this guide.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit. 

Garbage Disposal Repair or Replacement

×