A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.

Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.

If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.

Most plumbing problems associated with holiday parties are caused by improper plumbing maintenance and overestimations of your plumbing system’s abilities. Although it’s best if you have a professional plumber inspect your system before any large gathering, many plumbing problems can be prevented with a little knowledge and preparation before the big day. Remember, the best offense is a good defense. Schedule annual plumbing maintenance to keep your entire plumbing system healthy and efficient. Current problems will be addressed and future problems will be detected.
If the disposal is plugged in and doesn’t need to be reset, then you should check the circuit breaker. The breaker could be flipped, which would mean your disposal isn’t getting power. If that’s still not the problem, then either the outlet is dead, the circuit breaker is malfunctioning, or the disposal needs to be replaced. Check the outlet first by plugging something else into it. If the outlet works, try replacing the circuit breaker switch. If that isn’t it either, you have to replace the disposal.
Not every garbage disposal was created equal, and it can be difficult to discern which one is right for your home. After all, a quick internet search will show you that there are hundreds of different models to choose from. You shouldn’t automatically choose the cheapest or best rated garbage disposal. You need to find the one that is right for your unique needs.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.

Garbage Disposal Repair

×