Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.
Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.

If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)

A garbage disposal unit (also known as a garbage disposal, waste disposal unit, garbage disposer, or in Canadian English a garburator) is a device, usually electrically powered, installed under a kitchen sink between the sink's drain and the trap. The disposal unit shreds food waste into pieces small enough—generally less than 2 mm (0.079 in)—to pass through plumbing.[1]
Personally I'd recommend if you have a disposal have it removed. Most people don't realize, there is very little you are supposed to put in them. Whereas, they are the primary reason for your kitchen sink drain getting clogged. Just use the trash, it could save you an expensive Drain cleaning bill. Here's a tip for y'all who do have them. After use let warm water run while it's still running for 3 to 4 minutes, that will help push everything to the bigger main drain .
Jarred Connections: Considering the garbage-disposal systems is located under the kitchen sink, and since the area under the kitchen sink is a common place for storing all sorts of things, it is fairly common for the unit to get bumped.If it gets hit hard enough, the unit can actually shift so that it is no longer sitting straight. Pipes can also get knocked around, causing the seals to lose effectiveness.

Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.


Some towns and cities require a homeowner to get a permit before being allowed to install a new food disposal system. Others have outright outlawed the use of disposals due to limited sewer and water capacity. For example, an increasing number of cities in California has banned the installation of new garbage disposers in homes due to the ongoing drought the state is suffering from.
Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.

A garbage disposal unit (also known as a garbage disposal, waste disposal unit, garbage disposer, or in Canadian English a garburator) is a device, usually electrically powered, installed under a kitchen sink between the sink's drain and the trap. The disposal unit shreds food waste into pieces small enough—generally less than 2 mm (0.079 in)—to pass through plumbing.[1]
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!

Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.


If the garbage disposal won’t turn on, then it’s probably not getting power. First, make sure it’s plugged in. It’s easy to forget that disposals have wall outlets. It’s easy to knock a plug out of an outlet accidentally, especially in a dark place like under the sink. If the disposal is plugged in, check the reset button on the bottom of the disposal unit. If the disposal requires resetting, the button will be popped out. Simply press it and try the disposal again.

STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.


This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×