STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
If your garbage disposal is not running, first check to see if it is plugged in and receiving power. If so then check to see whether it will turn freely with your service wrench. Most disposers are sent with a self service wrench. The wrench is silver and should be located on or near your garbage disposal. (Check under your sink!) If it will not turn freely using the wrench, the disposal is most likely jammed. Check to see if the reset button has popped out.

Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.
Most blog writers make money from the links they include, so if someone is reading this and decides to click on a link and purchase the item, they receive a small sales commission per se. Mind you it takes hundreds to thousands of these blogs ranking high in google searches (I’m sure you have an issue with most people using googleopoly as well) in order to make any real money at it, but until other brands get on the bandwagon and pay instead of hoping for free advertising, great bloggers will continue to use what pays the bills. Or at least kicks you back a free tank of gas or two a year.

Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.

I am a researcher. I read every review - the good and the bad. I've read the Consumer Reports reviews, read the Amazon reviews, read the other, sketchier review websites like GreatGarbageDisposals.com (I made that one up but if you've done any research on the internet you get my point). I am writing this review to share what I learned about the product and about the many reviews I've read. My situation was that our 6 year old Badger froze up and simply quit on me, so a new one was in order.


I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung. 

Garbage Disposal

×