If you're replacing a commercial garbage disposal, then you'll either want the Drain Strainer with Crown Adapter or the Drain Strainer XL. Both of these models have a universal Crown Adapter on top that serves as a funnel to cover the hole once the commercial garbage disposal has been removed. Note that it doesn't actually attach to the sink bowl, but you'll adjust the legs to get your unit flush underneath the bottom of the sink.
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.

Not every garbage disposal was created equal, and it can be difficult to discern which one is right for your home. After all, a quick internet search will show you that there are hundreds of different models to choose from. You shouldn’t automatically choose the cheapest or best rated garbage disposal. You need to find the one that is right for your unique needs.
Dispose orange peels, or any citrus rinds, to freshen the disposal and keep it smelling clean, but cut them into slices first as large pieces of citrus peel, e.g. half a lime, can jam a disposal. You can also use pieces of citrus fruit that may be too old to consume, as long as they're not too spoiled to smell nice. You can freeze these pieces first, if you wish.

You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.

Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
As the saying goes, an ounce of prevention is worth a pound of cure; in other words, take care of your garbage disposal to prevent leaks from happening. Proper use, regular maintenance and frequent inspections for leaks will keep your disposal in top working order. If you experience any water leaks or burst pipes, please call us and we will be happy to help.
My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.
Flip the disposer over and unscrew the electrical cover plate on the bottom of the disposer by removing the cover plate screw. Again, be sure the power to the unit has been turned off at the electrical supply panel. Then disconnect the electrical cable connector. Pull out the wires and remove the wire nuts. Also unscrew the ground wire from the green ground screw. Be sure to save the electrical cable connector so you can use it again.
The Camorra was never a coherent whole nor a centralised organization. Instead, it has always been a loose confederation of different, independent groups or families. Each group was bound around kinship ties and controlled economic activities which took place in its particular territory. Each family clan took care of its own business, protected its territory, and sometimes tried to expand at another group’s expense. Although not centralized, there was some minimal coordination, to avoid mutual interference. The families competed to maintain a system of checks and balances between equal powers.[26]
She knew about the service call fee. The 4 On Your Side Investigation found that’s a common fee. Consumer Investigator Jodi Brooks called around to try to get an estimate from private plumbers for a garbage disposal replacement. None of the businesses we called would give an estimate over the phone. All of them wanted to look at the situation before committing to a price, and all wanted to charge a service fee to come out. Brooks found only one plumber who would come out without charging.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.

Hang the disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. The disposal will now hang by itself. Tighten the three mounting screws, ultimately tightening each screw a few turns at a time until the mounting assembly is evenly and tightly seated against the bottom of the sink.

GE, which is an acronym for General Electric, is an international conglomerate whose headquarters are based in New York City, New York. The company operates in many different segments, ranging from home appliances to transportation. In terms of gross revenue, GE is the sixth largest company firm in the United States. GE garbage disposals have won praise for their powerful motors and overall durability.
To preserve quality of life in the capital, the Moscow’s government sends streams of municipal waste into the surrounding regions. Greenpeace reports that 90 percent of Moscow’s waste goes to landfills in Moscow’s suburban region. Landfills created in the Soviet and early post-Soviet period, when there was little consumer waste, have been expanded, often with no community notification and despite being in close proximity to homes and schools. Air quality suffers as the dumps release fumes from decomposing waste.
Garbage disposals help us get rid of food waste, so it’s not surprising that the appliance may be susceptible to gross smells. A capful of bleach or grinding up citrus peels can help eliminate any foul odors coming from your garbage disposal. However, if nothing seems to help your appliance in the smell department, it may be catching food particles within its crevices. We recommend disassembling your garbage disposal to clean it, or replacing it if it’s old.

Last, but not least, as your garbage disposal system begins to age, it grows susceptible to cracking along its interior lining. When this shell develops cracks, water will begin to appear at its seams. At times, the leak can be observed from the bottom of the unit, particularly from the reset button. If this is the cause of your garbage disposal’s leaks, then there is no method of repairing other than replacing the whole unit.

Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
Like most appliances with moving parts, all kinds of stuff can go wrong in your disposal, for all sorts of reasons. Luckily, unlike many appliances, most disposals can be quickly and relatively easily fixed, as long as you’re careful and do your research. The next time you experience one of the following problems, follow these instructions and see if you can’t get things moving again.
To fix this problem, turn off the disposal, fill the sink halfway full with soapy water, and use a cup plunger to plunge the kitchen sink for 30 seconds to one minute. If you cleared the clog, the water in the sink should start draining at a normal pace again. If you’re still have issues, you might have to remove the P-trap under the sink to get at the clog with a snake.
Garbage disposals can range from $70 on the low end to $380 on the high end -- and generally speaking, you get what you pay for. A less expensive unit is likely to produce more noise, require more water, and clog more easily than a higher-end model. Likewise, a more expensive unit will be faster, quieter and less likely to malfunction than a lower end model -- and it will be lighter-weight and offer greater capacity as well. The average cost of a garbage disposal installation with a one-year manufacturer’'s warranty is $185. The average amount of time taken to install a garbage disposal, including cleanup, is three hours. The hourly cost for labor will range from $20 to $40 -- $28 on average.
Warranty - The average industry warranty on a garbage disposal is one year; however, it is not uncommon to see manufacturers’ warranties that can extend up to ten years. As a general rule of thumb, the more comprehensive and longer a warranty is, the more confidence the manufacturer has in the product they have made, but this is not always the case, so it is still important to do your homework.
Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.

If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Some jams you can free and get the motor to spin and sound like it is working, but the blades are stuck in one position and can’t spin freely to do their job properly. This is very common problem – the motor works so we think everything is working. Not the case! This can lead to stoppages, food trapped in the disposal and a bad smell. These blades can’t be repaired. The disposal needs to be replaced.

Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.

A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.

The bulk of a food waste disposer system, which includes the seals and pipes, is located beneath the kitchen sink. Most homeowners use this space to store various items, and it is not uncommon for people to bump or jar the disposal’s pipes when reaching for an item that is in close proximity. If the pipes are struck hard enough, the pipes can shift so that they are no longer sitting properly. Retaining bolts can become loose. Pipes may move, and seals can shift into an awkward position.

Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.