Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
The only existing hole I can think of ‘near the top’ that is a part of the unit, would be the place where a dishwasher hose would attach. Was that disposal once connected to a dishwasher that is no longer there? If so, that could be why water is coming out of ‘an existing hole’… Seems silly maybe, but sometimes the most obvious really is the answer.
Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
Some other kinds of garbage disposal units are powered by water pressure, rather than electricity. Instead of the turntable and grind ring described above, this alternative design has a water-powered unit with an oscillating piston with blades attached to chop the waste into fine pieces.[27] Because of this cutting action, they can handle fibrous waste. Water-powered units take longer than electric ones for a given amount of waste and need fairly high water pressure to function properly.[citation needed]
Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]
This may result in higher costs for energy needed to supply oxygen in secondary operations. However, if the waste water treatment is finely controlled, the organic carbon in the food may help to keep the bacterial decomposition running, as carbon may be deficient in that process. This increased carbon serves as an inexpensive and continuous source of carbon necessary for biologic nutrient removal.[31]
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

At one point, I did have a leak that I eventually determined was due to improper installation. (This was by the same "professional" plumber who reversed the hot and cold supply lines when installing a kitchen faucet. He just didn't connect the drain hose properly.) While investigating the issue, I called Waste King to inquire about possible in-home service or warranty replacement. I was blown away by their level of customer service: no waiting on hold, just an immediate connection to a person who really knew the product and was unexpectedly diligent in resolving my problem -- which, as it turns out, wasn't even their fault.

While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.
In 1998, police took a leading Camorra figure into custody. Francesco Schiavone was caught hiding in a secret apartment near Naples behind a sliding wall of granite. The mayor of Naples, Antonio Bassolino, compared the arrest to that of Sicilian Mafia chief Salvatore Riina in 1993.[43] Francesco Schiavone is now serving a life sentence after a criminal career which included arms trafficking, bomb attacks, armed robbery, and murder.
Here are some problems that every garbage disposal can run into, old or new. Learning about your garbage disposal and how it works (and how it doesn’t work, of course!) is the first step to decide if it simply needs a repair or if it needs to be replaced all together. One thing that stands for any and all situations: never stick your hands down the drain!
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.

I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
A foul or foreign odor emanating from the garbage disposal that won’t go away no matter how thoroughly you have rinsed it, may also be a sign that it’s time to replace it. As the components in the grinding chamber wear out and the blades get duller and duller, food can easily get trapped inside and start to decompose. You may never have noticed the smell or have chosen to adapt and wait it out, but it may be a sign of a deeper problem. Visiting family members and dinner guests probably wouldn’t appreciate it very much, either.

I'm not what you'd call a handyman, although I've been working to get better at that. I will now at least try a home project before passing on it. So, when our 15-year garbage disposal died I had another opportunity. I determined our old unit to be a Badger 5 1/2 HP (this exact item). I didn't have time to wait for the item to arrive from Amazon so I went to Home Depot and coughed up an extra $20 for the Badger 500 - Home Depot's branded version of this item. They are identical except for the name & sticker.

Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.
There you have it. If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.
The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.

Most plumbing problems associated with holiday parties are caused by improper plumbing maintenance and overestimations of your plumbing system’s abilities. Although it’s best if you have a professional plumber inspect your system before any large gathering, many plumbing problems can be prevented with a little knowledge and preparation before the big day. Remember, the best offense is a good defense. Schedule annual plumbing maintenance to keep your entire plumbing system healthy and efficient. Current problems will be addressed and future problems will be detected.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
×