If the water is leaking at the mounting assembly, make sure it is mounted as designed and not cocked. If the water is leaking at the dishwasher inlet, tighten the hose connector. If the water is leaking through the wall of the container body, your disposer probably need to be replaced. If the water is leaking from adjacent plumbing, tighten the connections as necessary.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.

Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
Even the most trustworthy garbage disposal will develop a leak from time to time; however, just because your food waste disposer has developed a leak does not necessarily mean that it needs to be replaced. Doing a little bit of investigating and troubleshooting before deciding to run out and buy a new garbage disposal can mean the difference between spending $10.00 for a replacement and $100.00+ to replace the entire unit.

See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.

Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Look for a jam. Something too tough to grind, such as a piece of glass, could be jamming the motor. Turn off the power and water, then unplug the disposal. (If it’s hardwired, turn off the breaker.) Remove the rubber baffle inside the drain-most just lift out-and shine a flashlight into the hole. Fish out the obstruction with a pair of tongs or needle-nose pliers.

Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
Here are some problems that every garbage disposal can run into, old or new. Learning about your garbage disposal and how it works (and how it doesn’t work, of course!) is the first step to decide if it simply needs a repair or if it needs to be replaced all together. One thing that stands for any and all situations: never stick your hands down the drain!
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
Although the name is most famously associated with their high quality mixers, KitchenAid garbage disposals have fared well in both professional and consumer written reviews. Founded in 1919, the KitchenAid brand is the only brand in the world that produces items strictly for the kitchen. KitchenAid offers both batch feed and continuous feed garbage disposal systems for residential and commercial settings.

If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
In the United States, almost all garbage disposals on the market are manufactured by a handful of companies; although, many are branded under different names. For example, out of the top ten highest rated models on the market, InSinkErator makes eight of them. Whirlpool and WasteKing are the other two most well-known brands in the U.S. There are a wide range of models to choose from, ranging from basic $50.00 models to models equipped with all of the latest bells and whistles that can cost as much as $600.00. In most cases, you get what you pay for in terms of quality. Here is a brief overview of the top brands in the U.S.
A foul or foreign odor emanating from the garbage disposal that won’t go away no matter how thoroughly you have rinsed it, may also be a sign that it’s time to replace it. As the components in the grinding chamber wear out and the blades get duller and duller, food can easily get trapped inside and start to decompose. You may never have noticed the smell or have chosen to adapt and wait it out, but it may be a sign of a deeper problem. Visiting family members and dinner guests probably wouldn’t appreciate it very much, either.
Some towns and cities require a homeowner to get a permit before being allowed to install a new food disposal system. Others have outright outlawed the use of disposals due to limited sewer and water capacity. For example, an increasing number of cities in California has banned the installation of new garbage disposers in homes due to the ongoing drought the state is suffering from.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
Scotland has had its brush with the Camorra. Antonio La Torre of Aberdeen was the local "Don" of the Camorra. He is the brother of Camorra boss Augusto La Torre of the La Torre clan which had its base in Mondragone, Caserta. The La Torre Clan's empire was worth hundreds of millions of euros. Antonio had several legitimate businesses in Aberdeen, whereas his brother Augusto had several illegal businesses there. He was convicted in Scotland and is awaiting extradition to Italy. Augusto would eventually become a pentito in January 2003, confessing to over 40 murders and his example would be followed by many of his men.[54]
Our most affordable large-capacity model ready to tackle Our most affordable large-capacity model ready to tackle meals of up to 750 persons with its powerful 3 HP motor. Like all InSinkErator food service disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as large banquet facilities ...  More + Product Details Close

In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]


In the 1970s and 1980s Raffaele Cutolo made an attempt to unify the Camorra families in the manner of the Sicilian Mafia, by forming the New Organized Camorra (Nuova Camorra Organizzata or NCO), but this proved unsuccessful. Drive-by shootings by camorristi often result in casualties among the local population, but such episodes are often difficult to investigate because of widespread omertà (code of silence). According to a report from Confesercenti, the second-largest Italian Trade Organization, published on October 22, 2007 in the Corriere della Sera, the Camorra control the milk and fish industries, the coffee trade, and over 2,500 bakeries in Naples.[28]
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
Chartered by entrepreneur Lowell Harrelson and Long Island mob boss Salvatore Avellino, it set sail on March 22 from Islip, New York,[2] escorted by the tugboat Break of Dawn and carrying 3,168 tons of trash headed for a pilot program in Morehead City, North Carolina, to be turned into methane. The barge was docked at Morehead City, until a WRAL-TV news crew, acting on a tip, flew by helicopter to the coast to investigate. Action News 5 Reporter Susan Brozek broke the story on the 6 p.m. news on April 1, 1987, and North Carolina officials began their own investigation, which resulted in an order for the Mobro to move on.
I believe if you always run your water first, turn on disposer, then discard food waste down disposer, you will get more longevity from your disposer and less likely have drain stoppage problems. It's also a good practice to run plenty of water (maybe even cleanser) after using the disposer to rinse out the small chamber between the blades and drain pipe. I've found that some disposer stoppages are caused by this chamber being clogged which also causes it to rust and deteriorate prematurely.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.

The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.

Our Minneapolis – St. Paul plumbers assist customers with garbage disposal installation by helping them choose between a continuous feed garbage disposal or a batch feed utility. Our plumbers will discuss the best options for your home and lifestyle. Some of the benefits of our garbage disposals include anti-jamming technology, plastic or metal blades, connectors to the dishwasher, system quietness, and more.


Badger Series garbage disposals are the choice of homeowners looking for hard-working helpers in the kitchen that are as tough on food waste as they are easy on the wallet. The value and price is unbeatable. A powerful, 1/2 HP Dura-Drive motor powers the Badger 5 through your food waste including: vegetables, fruits, leftovers, egg shells, celery stalks, and small bones.
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.

If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.


Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
An affordable option that offers outstanding value, the Waste King Legend Series comes backed by a solid five-year warranty. The stainless steel disposal is compact enough to install under most sinks. The continuous feed design means this disposal requires just a flip of a switch. It runs very quietly, but it is still powerful enough to grind food waste efficiently.

For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.
Badger Series garbage disposals are the choice of homeowners looking for hard-working helpers in the kitchen that are as tough on food waste as they are easy on the wallet. The value and price is unbeatable. A powerful, 1/2 HP Dura-Drive motor powers the Badger 5 through your food waste including: vegetables, fruits, leftovers, egg shells, celery stalks, and small bones.
How many years do garbage disposals last? One the average, quite a long time. In fact, with adequate care and proper maintenance, garbage disposal units can be of good service for about 8 to 15 years. This means the blades remain efficient and the motor has not burned out yet. This being said, neglecting garbage disposal leaks will significantly decrease this effective service life.
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?
Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”

Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
I thought that this might be underpowered (my last one almost had double the power, after all), but it has plenty of power to eat through whatever you throw at it. I don't dump EVERYTHING down the drain, but it takes what I give it with no problems. And the last garbage disposal was loud and raucous--yes, raucous. But this one is a pleasure. When you flip the switch, it makes a reassuring hum. It sounds more like a fine piece of machinery than a couple of animals fighting to the death inside my sink (like my old disposer).
Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
If you're replacing a commercial garbage disposal, then you'll either want the Drain Strainer with Crown Adapter or the Drain Strainer XL. Both of these models have a universal Crown Adapter on top that serves as a funnel to cover the hole once the commercial garbage disposal has been removed. Note that it doesn't actually attach to the sink bowl, but you'll adjust the legs to get your unit flush underneath the bottom of the sink.
The quick resolution of the Kuchino problem was covered favorably in the Russian media, but hardly represents a systemic response to the problem of municipal waste disposal. In fact, Putin’s recognition of what he called “the legitimate negative reaction of people” to widespread problems with trash disposal may have emboldened protesters near other landfills.
Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
Since the mid-1990s, the Camorra has taken over the handling of refuse disposal in the region of Campania, with disastrous results for the environment and the health of the general population. Heavy metals, industrial waste, chemicals and household garbage are frequently mixed together, then dumped near roads and burnt to avoid detection, leading to severe soil and air pollution.
Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
×