Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Although the name is most famously associated with their high quality mixers, KitchenAid garbage disposals have fared well in both professional and consumer written reviews. Founded in 1919, the KitchenAid brand is the only brand in the world that produces items strictly for the kitchen. KitchenAid offers both batch feed and continuous feed garbage disposal systems for residential and commercial settings.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.

Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]


We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
The origins of the Camorra are not entirely clear. It may date back to the 17th century as a direct Italian descendant of a Spanish secret society, the Garduña, founded in 1417. Officials of the Kingdom of Naples may have introduced the organization to the area, or it may have grown gradually out of small criminal gangs operating in Neapolitan society near the end of the 18th century.[3] However, recent historical research in Spain suggests that the Garduña never really existed and was based on a fictional 19th century book.[4]
The 2 800 RPM motor-powered dual stainless-steel swivel The 2 800 RPM motor-powered dual stainless-steel swivel impellers built into this GE 1/2 HP Continuous-Feed Garbage Disposal join forces with a 2-level pre-cutter to make it easy to grind undesirable waste into easily drainable particles. The disposer's large-capacity disposer chamber is comprised of a cold-rolled carbon steel armature shaft ...  More + Product Details Close
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
The first official use of the word dates from 1735, when a royal decree authorised the establishment of eight gambling houses in Naples. The word is likely a blend, or portmanteau, of "capo" (boss) and a Neapolitan street game, the "morra".[3][5] (In this game, two persons wave their hands simultaneously, while a crowd of surrounding gamblers guess, in chorus, at the total number of fingers exposed by the principal players.)[6] This activity was prohibited by the local government, and some people started making the players pay for being "protected" against the passing police.[3][7][8]
Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.
If the source is not a connection from above then your disposal needs to be replaced. Try cupping your hands around the very top under the sink while running water. The ring that seals the gasket turns clockwise to tighten. The only other repairable leak would be where the piping comes out the side. There can also be a smaller dishwasher drain hose above that.
The easiest way to apply that force is to squeeze them together using tongue-and-groove pliers, such as Channellocks. You’ll need medium or large pliers to do this. Unlike prying on the lower ring with a screwdriver or hex wrench-the method recommended in most instruction sheets-squeezing can’t disturb the position of the sink flange and cause it to leak. Plus, it’s easier on the wrists.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

Not every garbage disposal was created equal, and it can be difficult to discern which one is right for your home. After all, a quick internet search will show you that there are hundreds of different models to choose from. You shouldn’t automatically choose the cheapest or best rated garbage disposal. You need to find the one that is right for your unique needs.
The majority of today’s garbage disposals are designed to dovetail with a sink’s drain outlet, which makes connecting the two components simple. There are a multitude of connection kits and adaptors available. Many models feature a power cord that is simply plugged into a nearby outlet to power the unit; however, when an outlet is not available, the unit must be hardwired, which can be significantly more expensive.
Why am I writing a review about my beloved garbage disposal? Why am I referring to it as my "beloved" garbage disposal? I replaced a different garbage disposal from Costco; it had lasted a few years before giving up the ghost (the metal teeth within had basically corroded and broken off). Even before it met its untimely end, it had been loud and took a long time to grind things up--despite it being 1-1/4 horsepower!
Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close
Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
Most plumbing problems associated with holiday parties are caused by improper plumbing maintenance and overestimations of your plumbing system’s abilities. Although it’s best if you have a professional plumber inspect your system before any large gathering, many plumbing problems can be prevented with a little knowledge and preparation before the big day. Remember, the best offense is a good defense. Schedule annual plumbing maintenance to keep your entire plumbing system healthy and efficient. Current problems will be addressed and future problems will be detected.
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.

If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.

Garbage disposals might be one of the most underrated conveniences in modern kitchens — and it’s usually not until something goes wrong that we realize how truly valuable the appliance is. When it comes to garbage disposals, one of the most common problems homeowners report is a leak. But while a leaky garbage disposal is an annoyance, the issue is typically easy to fix. This no-frills guide will help you find the source of a leak and detail how you can remedy the issue with a little knowledge and DIY magic.
From the rich industrialist who wants a clear road into politics or administration to the small shopowner who wants to ask for a reduction of taxes; from the businessman trying to win a contract to a worker looking for a job in a factory; from a professional who wants more clients or greater recognition to somebody looking for an office job; from somebody from the provinces who has come to Naples to buy some goods to somebody who wants to emigrate to America; they all find somebody stepping into their path, and nearly all made use of them.[18]

Leaks from the bottom of the garbage disposal (often from the reset button) commonly indicate that at least one seal on the interior shell of the unit that protects the motor has deteriorated, or that the shell itself has cracked. These vulnerabilities can cause water from the sink to seep into the shell of the disposal and leak out of the base of the unit. In an old garbage disposal, one compromised internal seal is often accompanied by others, so your best bet is to install a new one.
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×