You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.
I bought this two years ago when planning a kitchen remodel for our retirement home. Since I was doing the remodel myself, it took two years, working part time. During that period I managed to lose the instructions for this air switch. Thank you for providing them. Now I can install it on the front of my Ikea kitchen sink cabinet. When/if I ever am in a wheelchair or walker, I will still be able to easily reach the disposal switch. WARNING: If you have a toddler, mount this where they can't easily reach it and send a matchbox car down your sink disposal in an imaginary carwash.
Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.

If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.

If there is nothing visible clogging your disposal unit, the flip switch on your garbage disposal unit may have turned the unit off. This little red switch is located underneath your unit and protects against overheating and arcing situations. You can try pushing the red switch to reset the garbage disposal unit. Test your unit by turning it on. If it still won't turn on or makes a humming noise, unplug the unit or turn it off at the breaker box, and move to step 4.
Many Camorra members and associates fled the internecine gang warfare and Italian Justice and immigrated to the United States in the 1980s. In 1993, the FBI estimated that there were 200 camorristi in the United States. Although there appears to be no clan structure in the United States, Camorra members have established a presence in Los Angeles, New York and Springfield, Massachusetts.[56] The Camorra is the least active of all the organized crime groups in the United States.[57] In spite of this, the US law enforcement considers the Camorra to be a rising criminal enterprise, especially dangerous because of its ability to adapt to new trends and forge new alliances with other criminal organizations.[58]
Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.

Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
If your disposal grinds poorly, make sure that you are running enough water while operating the unit and that you are not grinding matter that you shouldn’t. If you can hear the garbage disposal running but it is not grinding, the blades may be broken. It’s usually easier and cheaper to just replace the entire unit. See How to Install a Garbage Disposal.
STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:
Read the directions for your model before attempting a home repair. Most disposals have an electrical reset button, and a manual hex key for un-jamming. If the disposal stops working, its internal circuit breaker may have shut it off. Turn the switch definitely off, and try to pull out the hard object that may have jammed it. Then use the right-sized hex key to manually turn the rotor parts (usually directly under the unit in the center). If it turns, then push the reset button. It usually clicks in. Then, turn on the water and try the power, again.
Have you ever opened the cabinets under the sink to remove the trash or a handful of cleaning products, only to find everything soaked and soggy? Have you ever installed – or even had professionally installed – a brand new, state-of-the-art garbage disposal, only to have it flood your kitchen floor the next day? If so, you have a major plumbing: a leaking garbage disposal leaking from.
If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.
To preserve quality of life in the capital, the Moscow’s government sends streams of municipal waste into the surrounding regions. Greenpeace reports that 90 percent of Moscow’s waste goes to landfills in Moscow’s suburban region. Landfills created in the Soviet and early post-Soviet period, when there was little consumer waste, have been expanded, often with no community notification and despite being in close proximity to homes and schools. Air quality suffers as the dumps release fumes from decomposing waste.

If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)

Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.
Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.
While you were testing the red switch at the bottom of the unit, you may have noticed a small opening in the center. If the unit is clogged or humming, you can try to free up the unit by using the wrenchette (Hex-Torx key) that came with your unit or a 1/4 inch allen wrench. Simply place the wrench into the center hole and move it back and forth until the whatever is clogging your unit is dislodged. Once your unit is moving freely, turn it back on to test. If the unit still won't turn on, it may be necessary to take the unit apart.
Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.

If there is nothing visible clogging your disposal unit, the flip switch on your garbage disposal unit may have turned the unit off. This little red switch is located underneath your unit and protects against overheating and arcing situations. You can try pushing the red switch to reset the garbage disposal unit. Test your unit by turning it on. If it still won't turn on or makes a humming noise, unplug the unit or turn it off at the breaker box, and move to step 4.


In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.

The first official use of the word dates from 1735, when a royal decree authorised the establishment of eight gambling houses in Naples. The word is likely a blend, or portmanteau, of "capo" (boss) and a Neapolitan street game, the "morra".[3][5] (In this game, two persons wave their hands simultaneously, while a crowd of surrounding gamblers guess, in chorus, at the total number of fingers exposed by the principal players.)[6] This activity was prohibited by the local government, and some people started making the players pay for being "protected" against the passing police.[3][7][8]


Badger Series garbage disposals are the choice of homeowners looking for hard-working helpers in the kitchen that are as tough on food waste as they are easy on the wallet. The value and price is unbeatable. A powerful, 1/2 HP Dura-Drive motor powers the Badger 5 through your food waste including: vegetables, fruits, leftovers, egg shells, celery stalks, and small bones.
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
As advertised, it does come with a corded plug so it will need an outlet. My old Badger was a direct wire. Some folks tore out the cord and the strain relief as a fix and hard wired it like their old one. Some folks put an outlet in, which I found that to be a 15 minute job. I didn't want to mess around with chopping out the stock cord and putting in a new one and messing with the strain relief replacement. I thought the new outlet process was much easier because, heck, the wire's already there and that's always the hardest part of wiring a box! I shoved some of the extra length of the existing wire back into the hole in the wall that it came out from. I thought carefully about where the new box should go so the body of the disposal didn't hit it. I screwed it to the back of the cabinet, poked the wires into the box, screwed them to a new receptacle and, voila!. NOTE: IF YOU DON'T KNOW WHAT YOU'RE DOING WITH ELECTRICAL WIRING, DO NOT ATTEMPT THIS YOURSELF. If you do, be sure to kill the power at the circuit breaker and it is probably the easiest box you will install. Just make sure it is securely mounted into something besides the flimsy back panel of the cabinet.

Saviano alleges that from the 1980s, Italian gangsters ran a network of lucrative businesses in the city as well as many illegal rackets. Saviano said Scotland's third city, with no history of organized crime, was seen as an attractive safe haven away from the violent inter-gang bloodletting that had engulfed their Neapolitan stronghold of Mondragone. Saviano claims that before the Italian clans arrived, Aberdeen did not know how to exploit its resources for recreation and tourism. He further states that the Italians infused the city with economic energy, revitalised the tourist industry, inspired new import-export activities and injected new vigour in the real-estate sector. It thereby turned Aberdeen into a chic, elegant address for fine dining and important dealings.[55]
Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
In 1977, brothers Bob and Jim Gregory founded Texas Disposal Systems, Inc. with $10,000, one customer, one truck and plenty of determination. Building on a deep commitment to customer satisfaction and environmental preservation, the Gregory Family created a collection of businesses that has become one of the largest independently-owned solid waste collection and disposal companies in central Texas.
Scotland has had its brush with the Camorra. Antonio La Torre of Aberdeen was the local "Don" of the Camorra. He is the brother of Camorra boss Augusto La Torre of the La Torre clan which had its base in Mondragone, Caserta. The La Torre Clan's empire was worth hundreds of millions of euros. Antonio had several legitimate businesses in Aberdeen, whereas his brother Augusto had several illegal businesses there. He was convicted in Scotland and is awaiting extradition to Italy. Augusto would eventually become a pentito in January 2003, confessing to over 40 murders and his example would be followed by many of his men.[54]
Garbage disposals with stainless steel grinding blades and turntables make easy work of leftover meatloaf and biscuits. These blades will stay strong and last for years. High-power grinding motors hit maximum speeds quickly. This means jams and clogs are less likely to happen. Make sure to keep the faucet running for about 60 seconds after you turn off the disposal. Doing this ensures that all of the food particles make it down the hose.

One last thought - Beef bones? I see that Consumer Reports tests these things by measuring the fineness of the grind using beef bones. Do people really put beef bones down a garbage disposal on purpose? You might think I'm babying mine, or maybe that's why I didn't have excessive vibration when I use it, but I'll put the beef bones in the trash and grind up the rest of the stuff with this and be just fine for many years to come, I hope!


Here are some problems that every garbage disposal can run into, old or new. Learning about your garbage disposal and how it works (and how it doesn’t work, of course!) is the first step to decide if it simply needs a repair or if it needs to be replaced all together. One thing that stands for any and all situations: never stick your hands down the drain!

As I have mentioned, garbage disposers for most people are just another kitchen appliance that we tend to take for granted, and this is one of the reasons I decided to bring this website to the internet. I have come across many customers over the years that only seem to notice this “gadget” when it goes wrong, and believe it or not, most of the time they go wrong is because they’re not cared for properly.
×