Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.
Look for a jam. Something too tough to grind, such as a piece of glass, could be jamming the motor. Turn off the power and water, then unplug the disposal. (If it’s hardwired, turn off the breaker.) Remove the rubber baffle inside the drain-most just lift out-and shine a flashlight into the hole. Fish out the obstruction with a pair of tongs or needle-nose pliers.
With so many different models of garbage disposals to choose from, it can be difficult to figure out which one will best suit your needs, especially when you begin looking at all of the different features each model has to offer. Reading garbage disposal reviews will be much easier if you know what you are looking for. Here is a glossary of common features found on most modern garbage disposals:
At one point, I did have a leak that I eventually determined was due to improper installation. (This was by the same "professional" plumber who reversed the hot and cold supply lines when installing a kitchen faucet. He just didn't connect the drain hose properly.) While investigating the issue, I called Waste King to inquire about possible in-home service or warranty replacement. I was blown away by their level of customer service: no waiting on hold, just an immediate connection to a person who really knew the product and was unexpectedly diligent in resolving my problem -- which, as it turns out, wasn't even their fault.
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need a repair, unclogging, or replacement.
As a general rule of thumb, the heavier and bigger that a garbage disposal is, the more quietly it will operate – so long as it fits properly underneath your sink. Even though the sound dampening technology used in the design of garbage disposals has improved dramatically in the last 10 years, it is unrealistic to expect your garbage disposal to operate noise free. Under specific sinks, some disposals will be noisier than others due to the amount of vibration they produce. Ideally, you should look for a garbage disposal that features a nylon, insulated grinding chamber, like those produced by WasteKing.
If the water is leaking at the mounting assembly, make sure it is mounted as designed and not cocked. If the water is leaking at the dishwasher inlet, tighten the hose connector. If the water is leaking through the wall of the container body, your disposer probably need to be replaced. If the water is leaking from adjacent plumbing, tighten the connections as necessary.
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
The easiest way to apply that force is to squeeze them together using tongue-and-groove pliers, such as Channellocks. You’ll need medium or large pliers to do this. Unlike prying on the lower ring with a screwdriver or hex wrench-the method recommended in most instruction sheets-squeezing can’t disturb the position of the sink flange and cause it to leak. Plus, it’s easier on the wrists.
Prior to testing the garbage disposal for leaks, unplug it at the wall outlet and turn off the power from the breaker box to prevent electrical shock. Then insert a watertight sink stopper into your sink drain and wipe the unit dry with a clean cloth. In any handy container, mix a few drops of food coloring into a few cups of water, and pour the dyed water onto the sink stopper to help you locate the leak.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.
Inspect each of these locations while gliding a light-colored rag over the unit; the dyed water will readily show on the rag and reveal the location of the leak. If a leak isn’t immediately apparent, remove the sink stopper and pour a few more cups of dyed water down the sink drain, then check for leaks again. Leaks near the top of the unit are more likely to show themselves while the sink is plugged, while side and bottom leaks are more noticeable while the sink is unplugged.
2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.
After watching this video, I decided I could replace my garbage disposer myself. Honestly, I think your site completely misrepresents how VERY difficult it is to hold up a 20+ pound disposal unit firmly up against the mounting hardware as you are literally crammed under your kitchen sink and then try and somehow get all three tabs to slide into place. I was very disappointed and, after 4 nights of trying and retrying, finally just called a plumber. Please don’t show anyone lifting something that is big and heavy and make it seems as light as a feather. Shame. Shame.
In the event that you do not have a grounded outlet to power the garbage disposal, you will need to install one. Adding a grounded outlet may cost as little as $5 when existing electrical wiring is placed a short distance away, plus an additional $75 for the electrician's labor. If a new grounded outlet needs to be added and electrical wiring does not yet exist, it will likely cost around $90, depending on labor and parts. If your project requires the addition of a new switch and wire, plan to spend an average of $5 to $10 on materials, plus about 30 minutes of labor at an average cost of $75 an hour.
Assuming that you have already given the disposal the time it needs to run and clear the garbage, you probably have a congested drain line. We don’t recommend using chemical drain cleaners with a garbage disposal. You will very likely just damage the unit and end up with a sink full of toxic chemicals that you’ll eventually be forced to clean out manually. If the blockage doesn’t go down with the good ol’ baking soda and vinegar remedy, then calling a John Moore professional is your best bet. He or she will know exactly how to properly remove the bolts, disconnect the drain trap and remove the trap and the discharge drain pipe, check for clogs and any other obstructions, and finally clear the blockage with the latest and best tools. (See our previous post about good steps you can take when your kitchen sink is clogged!)