Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.

Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.

Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
Watch the video below for tips on fixing your garbage disposal unit, including instructions for how to take it apart. If your unit still won't work, then you probably have a burned out motor or an electrical problem, which requires the expertise of a professional. This is when you'll want to call a plumber to replace your garbage disposal unit. It's a fairly difficult DIY project to replace your garbage disposal unit, but if you're up to it, here is a DIY guide for garbage disposal replacement.
We’ve Gone Paperless: During the last few years, the City has introduced new technologies that have encouraged employees to use electronic records whenever possible. The City Council reads and reviews their Agendas and related documents online, records are kept in an electronic format, and employees are encouraged to utilize shared networks to collaborate on projects and documents rather than printing drafts. Reducing paper usage not only helps our environment, but also saves money for office supplies.
Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
This is a heavy-duty stopper that does the job well for my light use in the kitchen. The only remark I'll make is that I always lift out garbage disposal stoppers and strainers after each use and keep them inverted with the concave side down over the drain so they dry out completely. The stopper isn't doing anything for you in between uses, so there's no sense in keeping it seated tightly in the drain. Keep it inverted and dried out to prevent disgusting scum from accumulating rapidly.
Manufactured in the United States, Waste King garbage disposals have won much praise for their energy efficient design. Waste King offers a wide range of garbage disposers for both residential and commercial settings. In the early 2000s, Waste King refocused their sights on providing unparalleled customer service and quality products, and their warranties are the current industry standard that others are measured by.
Saviano alleges that from the 1980s, Italian gangsters ran a network of lucrative businesses in the city as well as many illegal rackets. Saviano said Scotland's third city, with no history of organized crime, was seen as an attractive safe haven away from the violent inter-gang bloodletting that had engulfed their Neapolitan stronghold of Mondragone. Saviano claims that before the Italian clans arrived, Aberdeen did not know how to exploit its resources for recreation and tourism. He further states that the Italians infused the city with economic energy, revitalised the tourist industry, inspired new import-export activities and injected new vigour in the real-estate sector. It thereby turned Aberdeen into a chic, elegant address for fine dining and important dealings.[55]
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.
Locate the leak. Wipe off the disposal unit with a dry rag. Run water into the unit and turn it on. There are four places where the disposal unit may leak. At the top main seal, at the drain pipe, at the optional dishwasher inlet or along the garbage disposal body. Notice where the water is coming from. If the unit is wet at the very top, the main seal is leaking. If the area beneath the drain pipe is wet, the gasket is leaking. If the hose from the dishwasher feed drips, the hose or clamp may be faulty. If water is running out the bottom of the unit but the inlets and outlet are dry, the unit itself has developed a leak and must be replaced.
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.
Read the directions for your model before attempting a home repair. Most disposals have an electrical reset button, and a manual hex key for un-jamming. If the disposal stops working, its internal circuit breaker may have shut it off. Turn the switch definitely off, and try to pull out the hard object that may have jammed it. Then use the right-sized hex key to manually turn the rotor parts (usually directly under the unit in the center). If it turns, then push the reset button. It usually clicks in. Then, turn on the water and try the power, again.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Garbage Disposal Repair or Replacement

×