If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
Lay the disposal on its side under the sink so you can make the electrical connections. Make sure the circuit breaker is off. Remove the plate on the bottom of the disposal to expose the wiring and use wire connectors to connect the wires from the disposal to the matching wires from the power supply. Finally, secure the power cord to the bottom of the disposal using the proper connection. Replace the plate to cover the wires. (See Fig 6)
Locate the leak. Wipe off the disposal unit with a dry rag. Run water into the unit and turn it on. There are four places where the disposal unit may leak. At the top main seal, at the drain pipe, at the optional dishwasher inlet or along the garbage disposal body. Notice where the water is coming from. If the unit is wet at the very top, the main seal is leaking. If the area beneath the drain pipe is wet, the gasket is leaking. If the hose from the dishwasher feed drips, the hose or clamp may be faulty. If water is running out the bottom of the unit but the inlets and outlet are dry, the unit itself has developed a leak and must be replaced.

Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
The InSinkErator Badger 1 Continuous Feed Garbage Disposal 1/3 HP features a quick-mounting system that allows for easy installation or replacement. This sturdy garbage Disposal is constructed from galvanized steel and features a 26 oz. chamber for space-saving waste disposal. The garbage Disposal also features a 1/3 HP motor that rapidly grinds food waste for easy rinsing down the drain.
A: A leaking garbage disposal often goes unnoticed until you confront a sopping cabinet, a foul-smelling puddle, or an audible drip-drip-drip from the unit. The fix can be frustrating, too, because the leak can stem from a number of components in the system. Fortunately, with a little sleuthing, you can zero in on the leak and—depending on the exact location—stop the icky oozing and repair the component that caused it. Worst case scenario, if it turns out that the garbage disposal must be replaced, installing a new one is a reasonable do-it-yourself task for those with basic plumbing skills. Read on to keep the cash you’d otherwise hand over to a pro.

Prior to testing the garbage disposal for leaks, unplug it at the wall outlet and turn off the power from the breaker box to prevent electrical shock. Then insert a watertight sink stopper into your sink drain and wipe the unit dry with a clean cloth. In any handy container, mix a few drops of food coloring into a few cups of water, and pour the dyed water onto the sink stopper to help you locate the leak.


Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
This may result in higher costs for energy needed to supply oxygen in secondary operations. However, if the waste water treatment is finely controlled, the organic carbon in the food may help to keep the bacterial decomposition running, as carbon may be deficient in that process. This increased carbon serves as an inexpensive and continuous source of carbon necessary for biologic nutrient removal.[31]
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Garbage Disposal Repair or Replacement

×