Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
She knew about the service call fee. The 4 On Your Side Investigation found that’s a common fee. Consumer Investigator Jodi Brooks called around to try to get an estimate from private plumbers for a garbage disposal replacement. None of the businesses we called would give an estimate over the phone. All of them wanted to look at the situation before committing to a price, and all wanted to charge a service fee to come out. Brooks found only one plumber who would come out without charging.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.
Most blog writers make money from the links they include, so if someone is reading this and decides to click on a link and purchase the item, they receive a small sales commission per se. Mind you it takes hundreds to thousands of these blogs ranking high in google searches (I’m sure you have an issue with most people using googleopoly as well) in order to make any real money at it, but until other brands get on the bandwagon and pay instead of hoping for free advertising, great bloggers will continue to use what pays the bills. Or at least kicks you back a free tank of gas or two a year.
If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
Food scraps range from 10% to 20% of household waste, and are a problematic component of municipal waste, creating public health, sanitation and environmental problems at each step, beginning with internal storage and followed by truck-based collection. Burned in waste-to-energy facilities, the high water-content of food scraps means that their heating and burning consumes more energy than it generates; buried in landfills, food scraps decompose and generate methane gas; a greenhouse gas which contributes to climate change.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
As the saying goes, an ounce of prevention is worth a pound of cure; in other words, take care of your garbage disposal to prevent leaks from happening. Proper use, regular maintenance and frequent inspections for leaks will keep your disposal in top working order. If you experience any water leaks or burst pipes, please call us and we will be happy to help.
If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.
Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.
If the water is leaking at the mounting assembly, make sure it is mounted as designed and not cocked. If the water is leaking at the dishwasher inlet, tighten the hose connector. If the water is leaking through the wall of the container body, your disposer probably need to be replaced. If the water is leaking from adjacent plumbing, tighten the connections as necessary.
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:
Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
If your disposal grinds poorly, make sure that you are running enough water while operating the unit and that you are not grinding matter that you shouldn’t. If you can hear the garbage disposal running but it is not grinding, the blades may be broken. It’s usually easier and cheaper to just replace the entire unit. See How to Install a Garbage Disposal.
If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
When well-intentioned citizens confront unaccountable officials, their activities can become more political. I interviewed a municipal civic group leader from St. Petersburg who works on urban ecology and waste. He commented that it has become clear that government officials are responsive not to citizens, but to those “from above” who put them in their offices.
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.