Personally I'd recommend if you have a disposal have it removed. Most people don't realize, there is very little you are supposed to put in them. Whereas, they are the primary reason for your kitchen sink drain getting clogged. Just use the trash, it could save you an expensive Drain cleaning bill. Here's a tip for y'all who do have them. After use let warm water run while it's still running for 3 to 4 minutes, that will help push everything to the bigger main drain .
Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.
The quick resolution of the Kuchino problem was covered favorably in the Russian media, but hardly represents a systemic response to the problem of municipal waste disposal. In fact, Putin’s recognition of what he called “the legitimate negative reaction of people” to widespread problems with trash disposal may have emboldened protesters near other landfills.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.
You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.
Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.
My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.
Russian activists have come under increasing pressure since Putin returned to office in 2012. Protests have been relatively scarce after the 2011-2012 Bolotnaya demonstrations in response to election fraud. Long-standing nongovernmental groups working on environmental and human rights issues, which relied in part on funding from abroad, have been labeled “foreign agents” by Russia’s Ministry of Justice.
Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
Lowe's offers garbage disposals like the InSinkErator Evolution and Badger garbage disposals in various horsepower options. Models with lower horsepower tend to become jammed easily. What if your garbage disposal jams? No problem. Simply locate the hex socket in the center of the underside of the disposal. Grab a hex wrench, put it in the socket, and work it back and forth until you feel the blades loosen up. Once the blades are spinning freely, press the garbage disposal reset button. It's that easy. 

Flip the disposer over and unscrew the electrical cover plate on the bottom of the disposer by removing the cover plate screw. Again, be sure the power to the unit has been turned off at the electrical supply panel. Then disconnect the electrical cable connector. Pull out the wires and remove the wire nuts. Also unscrew the ground wire from the green ground screw. Be sure to save the electrical cable connector so you can use it again.
The evolution into more organized formations indicated a qualitative change: the Camorra and camorristi were no longer local gangs living off theft and extortion; they now had a fixed structure and some kind of hierarchy. Another qualitative leap was the agreement of the liberal opposition and the Camorra, following the defeat in the 1848 revolution. The liberals realized that they needed popular support to overthrow the king. They turned to the Camorra and paid them, the camorristi being the leaders of the city’s poor. The new police chief, Liborio Romano, turned to the head of the Camorra, Salvatore De Crescenzo, to maintain order and appointed him as head of the municipal guard.[11] The Camorra effectively had developed into power brokers in a few decades.[9] In 1869, Ciccio Cappuccio was elected as the capintesta (head-in-chief) of the Camorra by the twelve district heads (capintriti), succeeding De Crescenzo after a short interregnum.[12] Nicknamed 'The king of Naples' ('‘o rre 'e Napole) he died in 1892.[13][14]
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
Español: limpiar un triturador de basura, Português: Limpar um Triturador de Alimentos, Italiano: Pulire un Tritarifiuti da Lavandino, Deutsch: Den Küchenabfallzerkleinerer reinigen, Français: nettoyer votre broyeur d'évier, 中文: 清洁垃圾处理器, Русский: почистить утилизатор отходов, Bahasa Indonesia: Membersihkan Saluran Pembuangan Sampah, Nederlands: Je afvalvermaler schoonmaken, العربية: تنظيف مصرف النفايات
Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.
Most garbage disposal manufacturers provide a range of models to choose from with ever-increasing power ratings. If you do a ton of cooking and use your disposal frequently, then spending a little extra on a 3/4 or 1 horsepower disposal will absolutely be worth the money. Not only do the more powerful units shred through food scraps much easier, but they can also handle harder objects such as bones or meat scraps that might jam a smaller, weaker disposal. As mentioned before, powerful disposals are less noisy and they tend to have only occasional damages. However, one downside of having larger, more powerful disposal is that they will require more space. No matter what your habits, likes, and dislikes are, it’s always best to consult with a John Moore tech before buying a new disposal to make sure it will fit under your sink and perform how you need it to.
Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.
Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
In the event that you do not have a grounded outlet to power the garbage disposal, you will need to install one. Adding a grounded outlet may cost as little as $5 when existing electrical wiring is placed a short distance away, plus an additional $75 for the electrician's labor. If a new grounded outlet needs to be added and electrical wiring does not yet exist, it will likely cost around $90, depending on labor and parts. If your project requires the addition of a new switch and wire, plan to spend an average of $5 to $10 on materials, plus about 30 minutes of labor at an average cost of $75 an hour.
Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Look for a jam. Something too tough to grind, such as a piece of glass, could be jamming the motor. Turn off the power and water, then unplug the disposal. (If it’s hardwired, turn off the breaker.) Remove the rubber baffle inside the drain-most just lift out-and shine a flashlight into the hole. Fish out the obstruction with a pair of tongs or needle-nose pliers.

Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.


Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
Leaks from the bottom of the garbage disposal (often from the reset button) commonly indicate that at least one seal on the interior shell of the unit that protects the motor has deteriorated, or that the shell itself has cracked. These vulnerabilities can cause water from the sink to seep into the shell of the disposal and leak out of the base of the unit. In an old garbage disposal, one compromised internal seal is often accompanied by others, so your best bet is to install a new one.
"Thank you for creating a product that will help reduce the need to call a plumber every 2-3 weeks. I have tried various options to get my staff to take better care of what goes down the 3 compartment sink drain but it did not work. The Drain Strainer makes it extremely simple for them. The first two XL's that I ordered have worked perfectly. These additional two I ordered are for a different location and we expect the same results there." Jim Abanto - Owner El Chalan Restaurant - Miami FL
Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.

You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.


Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.
Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
Waste disposal units may jam, but can usually be cleared either by forcing the turntable round from above or by turning the motor using a hex-key wrench inserted into the motor shaft from below.[25] Especially hard objects accidentally or deliberately introduced, such as metal cutlery, can damage the waste disposal unit and become damaged themselves, although recent advances, such as swivel impellers, have been made to minimize such damage.[citation needed] More problematic are drain blockages caused by shredded waste that is fibrous, e.g., artichoke leaves, or starchy, e.g., potato peelings.
×