Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.

There you have it. If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.

First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.
The garbage disposal in your kitchen sink is a convenient way to get rid of scraps and leftovers, but when a foreign object like a glass gets caught in it, it can jam the mechanism and stop it from working. Removing a glass from a garbage disposal involves removing any large pieces of glass; dislodging the glass by inserting a wrench or broom handle into the bottom or top of the disposal; vacuuming the disposal; resetting it; or if none of the other steps work, removing the disposal and shaking out all of the glass. Read the following steps to find out how to remove a glass from a garbage disposal.

If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.

Once you have a garbage disposer installed, maintenance is what keeps your unit going. By following this link, you will find a very easy to follow video which details some simple steps to help keep your disposal unit clean, and your kitchen free of bad smells and harmful bacteria. You see, my website isn’t just about telling you to buy this model or that right now or you’ll miss out on some good deals (although I have mentioned a couple of places you can take a look at if you’re interested), it’s about making sure you get the best from your garbage disposer.

Lowe's offers garbage disposals like the InSinkErator Evolution and Badger garbage disposals in various horsepower options. Models with lower horsepower tend to become jammed easily. What if your garbage disposal jams? No problem. Simply locate the hex socket in the center of the underside of the disposal. Grab a hex wrench, put it in the socket, and work it back and forth until you feel the blades loosen up. Once the blades are spinning freely, press the garbage disposal reset button. It's that easy.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
The snap ring fits into a groove on the lower end of the sink flange. When you’re working under the sink, it prevents the upper mounting bracket from falling off. Removing an old snap ring can be frustrating-unless you know this trick: Starting at the break in the ring, insert a thin-blade screwdriver between the ring and the flange. Pull down on the ring with the screwdriver’s blade and walk the blade around the ring. The ring will pop right off.
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.
Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!

InSinkErator is a brand name that is well-known for their design and manufacturing of waste disposal systems and instant hot water dispensers. John Hammes founded the company in 1927 in Racine, Wisconsin, where their headquarters remain today. Hammes is credited with designing and producing the first “in sink” waste disposal system, and the InSinkErator is a play on the word “incinerator”. Currently, InSinkErator produces and markets garbage disposal systems under the Evolution and Badger Series brand names.


Locate the circuit breaker that controls power to the garbage disposal, and flip it to the "off" position before continuing. Fix or replace the main seal if it is leaking. Remove both the drain pipe and the dishwasher hose, if applicable. Insert a screwdriver into the tightening ring and turn it counterclockwise. This will release the garbage disposal unit. Inspect the main seal that sits on the top of the unit. The seal is a large, soft rubber fitting that covers the top edge of the garbage disposal. If dirt, grit or food particles have fouled the main seal, wipe it down with a damp rag and reinstall the disposal unit. If the main seal is cracked, pitted or broken, it needs to be replaced. Once a new main seal has been inserted into the garbage disposal, push it up against the mounting bracket, insert a screwdriver into the tightening ring, and turn it clockwise to lock the unit into place. Reinstall the drain pipe and dishwasher hose, if applicable.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close
We apologize in advanced for stating the obvious, but… garbage disposals absolutely do not last forever! No matter how well it’s made or how much money you spend, any appliance that is exposed to thousands of gallons of running water, dish soap, scraps of food, bones, and the rare (we hope) spoon or lime wedge that accidentally gets dropped into the drain is going to wear out in due time. A unit that’s working well should be able to handle a few scraps of veggies or apple slices in a matter of a couple of seconds. If your garbage disposal seems to take forever to accomplish a simple grinding job, makes a strange noise or emits a nasty smell, it may be time to install a new one.
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.

You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
4. Is installing a garbage disposal worth the additional water expense? On average, a modern faucet runs 2.5 gallons of water per minute, or 900 gallons per year based upon the average annual household usage in the U.S. Depending on how often you use your disposerl, your home’s water usage, and water bill, will rise. This is one factor you’ll need to consider before deciding whether or not to buy a garbage disposal.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

Garbage Disposal Installation

×