InSinkErator is a brand name that is well-known for their design and manufacturing of waste disposal systems and instant hot water dispensers. John Hammes founded the company in 1927 in Racine, Wisconsin, where their headquarters remain today. Hammes is credited with designing and producing the first “in sink” waste disposal system, and the InSinkErator is a play on the word “incinerator”. Currently, InSinkErator produces and markets garbage disposal systems under the Evolution and Badger Series brand names.
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.

3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
If the water is leaking at the mounting assembly, make sure it is mounted as designed and not cocked. If the water is leaking at the dishwasher inlet, tighten the hose connector. If the water is leaking through the wall of the container body, your disposer probably need to be replaced. If the water is leaking from adjacent plumbing, tighten the connections as necessary.

If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
In the 1970s, the Sicilian Mafia convinced the Camorra to convert their cigarette smuggling routes into drug smuggling routes with the Sicilian Mafia's assistance. Not all Camorra leaders agreed, leading to the Camorra Wars that cost 400 lives. Opponents of drug trafficking lost the war. The Camorra made a fortune in reconstruction after an earthquake ravaged the Campania region in 1980. Now it specializes in cigarette smuggling and receives payoffs from other criminal groups for any cigarette traffic through Italy. The Camorra is also involved in money laundering, extortion, alien smuggling, robbery, blackmail, kidnapping, political corruption, and counterfeiting. It is believed that nearly 200 Camorra affiliates reside in this country, many of whom arrived during the Camorra Wars.[59]
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.

If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.
Thank you for sharing this tutorial. My husband and I tried to fix our garbage disposal last week but we couldn’t get it to work. When we turn it on, it makes a humming noise, but nothing is blocking the blades. We might need to get a new disposal, but we’ll probably have a professional look at it before we decide. We’ll keep your tips on hand, just in case.

The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
Leaks from the bottom of the garbage disposal (often from the reset button) commonly indicate that at least one seal on the interior shell of the unit that protects the motor has deteriorated, or that the shell itself has cracked. These vulnerabilities can cause water from the sink to seep into the shell of the disposal and leak out of the base of the unit. In an old garbage disposal, one compromised internal seal is often accompanied by others, so your best bet is to install a new one.
The first official use of the word dates from 1735, when a royal decree authorised the establishment of eight gambling houses in Naples. The word is likely a blend, or portmanteau, of "capo" (boss) and a Neapolitan street game, the "morra".[3][5] (In this game, two persons wave their hands simultaneously, while a crowd of surrounding gamblers guess, in chorus, at the total number of fingers exposed by the principal players.)[6] This activity was prohibited by the local government, and some people started making the players pay for being "protected" against the passing police.[3][7][8]

No need to worry if your garbage disposal is on the fritz—installing a new one is a straightforward project that you can do yourself in just a few minutes. Start by switching off the power to the disposal at your home’s breaker box to ensure that you can work safely. Next, remove the old unit by detaching it from the mounting ring directly beneath the sink drain. Finally, install any necessary new mounting hardware, fit the new disposal into place, and turn on the water to test for leaks before giving it a trial run.

Our most affordable large-capacity model ready to tackle Our most affordable large-capacity model ready to tackle meals of up to 750 persons with its powerful 3 HP motor. Like all InSinkErator food service disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as large banquet facilities ...  More + Product Details Close

What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.


I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Even the most trustworthy garbage disposal will develop a leak from time to time; however, just because your food waste disposer has developed a leak does not necessarily mean that it needs to be replaced. Doing a little bit of investigating and troubleshooting before deciding to run out and buy a new garbage disposal can mean the difference between spending $10.00 for a replacement and $100.00+ to replace the entire unit.

Kitchen waste disposal units increase the load of organic carbon that reaches the water treatment plant, which in turn increases the consumption of oxygen.[28] Metcalf and Eddy quantified this impact as 0.04 pound of biochemical oxygen demand per person per day where disposers are used.[29] An Australian study that compared in-sink food processing to composting alternatives via a life cycle assessment found that while the in-sink disposer performed well with respect to climate change, acidification, and energy usage, it did contribute to eutrophication and toxicity potentials.[30]
×