Aside from the reviews I’ve put together, I haven’t forgotten about people who are having issues with their current food waste disposer. Below you will find some links to the information pages I’ve put together that will help you fix problems you might already have. For those of you that are confused over how to unclog a waste disposal unit, take a look at this page. On the same page, we also discuss waste disposal units that won’t power up and units that are leaking.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.

You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.

Garbage Disposal Install


First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
Ensure the breaker that controls the garbage disposal is off. Inspect the inlet hose from the dishwasher. If the leak is coming from a crack in the fixture itself, the unit needs to be replaced. If the hose has cracked or frayed, unscrew the clamp and remove it from the disposal unit. Cut off the end of the hose with a utility knife up to the point where the leak began. Dishwasher hoses provide plenty of slack, so cutting off a few inches should not be a problem. Slide the hose back onto the fixture, and reinstall the clamp.
In 1998, police took a leading Camorra figure into custody. Francesco Schiavone was caught hiding in a secret apartment near Naples behind a sliding wall of granite. The mayor of Naples, Antonio Bassolino, compared the arrest to that of Sicilian Mafia chief Salvatore Riina in 1993.[43] Francesco Schiavone is now serving a life sentence after a criminal career which included arms trafficking, bomb attacks, armed robbery, and murder.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
Since the mid-1990s, the Camorra has taken over the handling of refuse disposal in the region of Campania, with disastrous results for the environment and the health of the general population. Heavy metals, industrial waste, chemicals and household garbage are frequently mixed together, then dumped near roads and burnt to avoid detection, leading to severe soil and air pollution.
If you’re unsuccessful using the wrench, you may need to go in through the drain in an attempt to remove the clog. Disconnect the power to the disposal by unplugging the unit or turning off its circuit breaker, then use long-handled tongs and a flashlight to try to remove the jam.  Never use your hands for this task, even if the disposal is completely disconnected from its power source! Fumbling blindly around a disc of sharp blades is asking for injury.

We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.

A clogged garbage disposal unit can leak when you try to operate it without removing the clogging. What clogs up garbage disposals? Normally this would be expandable food like rice and pasta. Even large animal bones can also result in clogging and possible leak. Although coffee grounds help eliminate odors, allowing it to accumulate in the drain of the disposer will result in clogging and potential leak.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.

Garbage disposals might be one of the most underrated conveniences in modern kitchens — and it’s usually not until something goes wrong that we realize how truly valuable the appliance is. When it comes to garbage disposals, one of the most common problems homeowners report is a leak. But while a leaky garbage disposal is an annoyance, the issue is typically easy to fix. This no-frills guide will help you find the source of a leak and detail how you can remedy the issue with a little knowledge and DIY magic.
Personally I'd recommend if you have a disposal have it removed. Most people don't realize, there is very little you are supposed to put in them. Whereas, they are the primary reason for your kitchen sink drain getting clogged. Just use the trash, it could save you an expensive Drain cleaning bill. Here's a tip for y'all who do have them. After use let warm water run while it's still running for 3 to 4 minutes, that will help push everything to the bigger main drain .
The horror movie image of victims having hands and arms severed in a garbage disposal is entirely a Hollywood invention. In reality, the blades inside a garbage disposal are rather dull grinders, not gleaming, razor-sharp sabers. That is not to say that a disposal should be taken lightly—it is indeed possible to be painfully injured if you don't practice basic safety measures. 
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.

Español: limpiar un triturador de basura, Português: Limpar um Triturador de Alimentos, Italiano: Pulire un Tritarifiuti da Lavandino, Deutsch: Den Küchenabfallzerkleinerer reinigen, Français: nettoyer votre broyeur d'évier, 中文: 清洁垃圾处理器, Русский: почистить утилизатор отходов, Bahasa Indonesia: Membersihkan Saluran Pembuangan Sampah, Nederlands: Je afvalvermaler schoonmaken, العربية: تنظيف مصرف النفايات
An affordable option that offers outstanding value, the Waste King Legend Series comes backed by a solid five-year warranty. The stainless steel disposal is compact enough to install under most sinks. The continuous feed design means this disposal requires just a flip of a switch. It runs very quietly, but it is still powerful enough to grind food waste efficiently.
Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.

Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.
Modern food waste disposers are often connected to your dishwasher’s drain pipe. This connection enables your dishwasher to rid itself of any leftover food scraps or residue that it might accumulate while washing your dishes. Where the dishwasher hose and the garbage disposal connect is a common source for leaks. The leaks most often occur when hose’s clamp is not secure enough. Leaks also develop when the dishwasher hose cracks. In order to fix this type of leak, you should either replace the cracked section of hose or tighten the clamp down.
This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
Look for a jam. Something too tough to grind, such as a piece of glass, could be jamming the motor. Turn off the power and water, then unplug the disposal. (If it’s hardwired, turn off the breaker.) Remove the rubber baffle inside the drain-most just lift out-and shine a flashlight into the hole. Fish out the obstruction with a pair of tongs or needle-nose pliers.

Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

The L-2600 garbage disposal unit is one of the brand’s best-sellers. Its glass-filled nylon grinding chamber allows a smoother and more quiet performance as opposed to a full stainless steel model. It’s also easy to install and doesn’t take up too much space. It even comes with a removable splash guard to keep all the food scraps down when disposing them.
Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
A leaky garbage disposal is not only a hassle, it’s also a mess and can also result in other problems if left unfixed. If you’re inexperienced in home improvement work, diagnosing the source of the leak may seem like quite a challenge. Make your life easier with the help of the information below. Once you start eliminating each possible option on your checklist, you should be able to identify the problem quite quickly.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
I believe if you always run your water first, turn on disposer, then discard food waste down disposer, you will get more longevity from your disposer and less likely have drain stoppage problems. It's also a good practice to run plenty of water (maybe even cleanser) after using the disposer to rinse out the small chamber between the blades and drain pipe. I've found that some disposer stoppages are caused by this chamber being clogged which also causes it to rust and deteriorate prematurely.
Update: As an aside, I also learned from my research that the best way to clean my disposal is to use citric acid. Having previously had no idea what citric acid was used for, I decided to order some from Amazon, going with the brand my sister uses: Citric Acid Powder - Ultra Fine Pure Powdered Crystals - Natural Preservative Food Grade Quality (16 oz) and gave it a whirl after 3 months of using my disposal. I let the citric acid sit with some water in the disposal for about ten minutes, and then I let it run for a solid 2 minutes. I repeated the procedure a few times and after about 30 minutes—wow, all the leftover gunk and food was flushed out of the disposal, leaving it clean with a very mild citrus scent. I feel like I’m becoming a real DIY at home kind of guy.

Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)
STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.

Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
×