I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Your garbage disposal is one of the biggest helpers in your kitchen. Without it, cleaning up after quick weeknight dinners, family feasts, and leisurely Sunday breakfasts would be much harder. While some garbage disposal problems can be fixed with a quick repair, sometimes it’s easier and more cost-efficient to replace the appliance. If you’re not sure whether or not to replace or repair your garbage disposal, check out these five signs your appliance is completely broken.
For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.
When something blocks your disposal unit’s flywheel, you will start hearing a low humming sound, and you know you’ve got a jam. Un-jamming a garbage disposal is something that depends on the specific unit you own. Every single one has a function to shut off when they are stuck to the point of stalling the motor. This is so the motor doesn’t burn out. However, they are also designed so that anyone (and we mean anyone!) can remove whatever it is that is blocking your unit. Underneath every unit is a small slot, and pretty much all of them come with a tiny little wrench to match it. These are most commonly called hex-head wrenches. Yes, that little tool that you probably have no idea where it could possibly be has a very specific and important purpose. Mind blown, right?
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
As I have mentioned, garbage disposers for most people are just another kitchen appliance that we tend to take for granted, and this is one of the reasons I decided to bring this website to the internet. I have come across many customers over the years that only seem to notice this “gadget” when it goes wrong, and believe it or not, most of the time they go wrong is because they’re not cared for properly.
Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control
IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

We apologize in advanced for stating the obvious, but… garbage disposals absolutely do not last forever! No matter how well it’s made or how much money you spend, any appliance that is exposed to thousands of gallons of running water, dish soap, scraps of food, bones, and the rare (we hope) spoon or lime wedge that accidentally gets dropped into the drain is going to wear out in due time. A unit that’s working well should be able to handle a few scraps of veggies or apple slices in a matter of a couple of seconds. If your garbage disposal seems to take forever to accomplish a simple grinding job, makes a strange noise or emits a nasty smell, it may be time to install a new one.
Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.

Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
If the source is not a connection from above then your disposal needs to be replaced. Try cupping your hands around the very top under the sink while running water. The ring that seals the gasket turns clockwise to tighten. The only other repairable leak would be where the piping comes out the side. There can also be a smaller dishwasher drain hose above that.
In 2017, in Moscow and St. Petersburg, my research found a substantial increase in grassroots groups oriented around “civic pride” and local volunteer initiatives. These new groups focus on the preservation of green spaces, litter collection, recycling, urban beautification and historic preservation. These efforts represent a new “environmentalism of daily life” more acceptable to the government.
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.
However, if your garbage disposal is fairly new, having the reset button repaired is a better choice, especially if your unit is still under warranty. If your unit is under warranty, the company will probably send out a repair man to fix the job. On the other hand, if your unit isn’t under warranty, it’s best to have a skilled technician complete the job unless you have experience doing this.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.

Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
Update: As an aside, I also learned from my research that the best way to clean my disposal is to use citric acid. Having previously had no idea what citric acid was used for, I decided to order some from Amazon, going with the brand my sister uses: Citric Acid Powder - Ultra Fine Pure Powdered Crystals - Natural Preservative Food Grade Quality (16 oz) and gave it a whirl after 3 months of using my disposal. I let the citric acid sit with some water in the disposal for about ten minutes, and then I let it run for a solid 2 minutes. I repeated the procedure a few times and after about 30 minutes—wow, all the leftover gunk and food was flushed out of the disposal, leaving it clean with a very mild citrus scent. I feel like I’m becoming a real DIY at home kind of guy.
A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.

If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 
As I have mentioned, garbage disposers for most people are just another kitchen appliance that we tend to take for granted, and this is one of the reasons I decided to bring this website to the internet. I have come across many customers over the years that only seem to notice this “gadget” when it goes wrong, and believe it or not, most of the time they go wrong is because they’re not cared for properly.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
There are many potential causes for a leaky garbage disposal.  Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable.  Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.

Run a few trays of ice cubes, orange peels and salt through the disposal to remove odors and keep your disposals clean. For really tough odors, add 1/2 cup of baking soda and 1/2 cup of vinegar and let it stand for 15 minutes before rinsing. Also, running ice through the disposal will actually sharpen the teeth, keeping foods from getting stuck in the unit.

I've always had Insinkerator garbage disposals so I just didn't know any better but now I do. Simply put, this is truly the king of garbage disposals. The amount of power it has is ridiculous and it will tear through just about any food I've thrown at it. Now, I have been hesitant to test it with some tougher items (I've heard stories of people feeding it chicken and rib bones) because I was always taught to be careful what you put down the disposal (a cheap wimpy unit in a relative's shore house seizes up with unpopped corn kernels and their home unit clogged with shredded zucchini). I have given it some things like apple cores though with absolutely no problem. I never would have put an apple core down my old Insinkerator. This king eats the core in about 3-5 seconds, if that. Completely gone. The thing that absolutely astounds me about this unit though is how QUIET it is. It's almost ridiculous. My old one, and most everyone else's I've ever heard sounds like an electric chain saw. This one sounds like someone is humming. When people come over I run it form them just to show off how quiet it is. I know. I'm weird. Add to that a lifetime warranty and this thing just cannot be beat for the money. Google it yourself and you will see how many people agree that this is the best value disposal available. The cheap Insinkerators will normally run you about $80. It's not that much more to get one of these and the benefits for the small price increase are totally worth it. For 50% more you get way more than a 50% better disposal. Of course you could spend $350 on the Insinkerator Elite but is that one going to be 300% better. I doubt it. If you found this review helpful please click yes below.

At the time, the Mobro 4000 incident was widely cited by environmentalists and the media as emblematic of the solid-waste disposal crisis in the United States due to a shortage of landfill space: almost 3,000 municipal landfills had closed between 1982 and 1987.[5] It triggered much national public discussion about waste disposal, and may have been a factor in increased recycling rates in the late 1980s and after.[6] It was this that caused it to be included in an episode of Penn & Teller: Bullshit! (season 2, episode 5) in which they debunk many recycling myths.


First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
Built-in trash compactors fit snuggly into your kitchen cabinetry. Having a built-in compactor means you have one less appliance occupying precious floor space. A convenient toe pedal opener lifts the top open for easy hands-free opening, and a removable drawer make it easy to clean and empty the compactor. Shop for new garbage disposals and trash compactors from JCPenney today!
If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.
To fix this problem, turn off the disposal, fill the sink halfway full with soapy water, and use a cup plunger to plunge the kitchen sink for 30 seconds to one minute. If you cleared the clog, the water in the sink should start draining at a normal pace again. If you’re still have issues, you might have to remove the P-trap under the sink to get at the clog with a snake.

If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.
No need to worry if your garbage disposal is on the fritz—installing a new one is a straightforward project that you can do yourself in just a few minutes. Start by switching off the power to the disposal at your home’s breaker box to ensure that you can work safely. Next, remove the old unit by detaching it from the mounting ring directly beneath the sink drain. Finally, install any necessary new mounting hardware, fit the new disposal into place, and turn on the water to test for leaks before giving it a trial run.
STEP 5 – If you are one of those rebellious types that never listens to wise instruction, then take off any rings and make sure that your hand is lubricated with liquid dish soap or cooking oil to reduce the risk of it getting stuck in the drain opening. Also, have a phone nearby. If your hand does get stuck, you can then call someone (using your other hand, presumably) to call a friend or 911 for rescue. If at all possible, don’t call a friend with a video camera phone, because they’ll probably embarass you by broadcasting your plight on YouTube.
Connect the connector pipe to the elbow and the adjacent sink. Use the connector pipe to connect the elbow piece to the T-fitting on the adjacent sink. The connector piece might need to be cut down to the correct length depending on your sink. Use the nuts and washers provided with your pipes to secure the pieces together using the tongue-and-groove pliers.[1]
There are many potential causes for a leaky garbage disposal.  Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable.  Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.

IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.

The first official use of the word dates from 1735, when a royal decree authorised the establishment of eight gambling houses in Naples. The word is likely a blend, or portmanteau, of "capo" (boss) and a Neapolitan street game, the "morra".[3][5] (In this game, two persons wave their hands simultaneously, while a crowd of surrounding gamblers guess, in chorus, at the total number of fingers exposed by the principal players.)[6] This activity was prohibited by the local government, and some people started making the players pay for being "protected" against the passing police.[3][7][8]


You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.
Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.
STEP 5 – If you are one of those rebellious types that never listens to wise instruction, then take off any rings and make sure that your hand is lubricated with liquid dish soap or cooking oil to reduce the risk of it getting stuck in the drain opening. Also, have a phone nearby. If your hand does get stuck, you can then call someone (using your other hand, presumably) to call a friend or 911 for rescue. If at all possible, don’t call a friend with a video camera phone, because they’ll probably embarass you by broadcasting your plight on YouTube.

To preserve quality of life in the capital, the Moscow’s government sends streams of municipal waste into the surrounding regions. Greenpeace reports that 90 percent of Moscow’s waste goes to landfills in Moscow’s suburban region. Landfills created in the Soviet and early post-Soviet period, when there was little consumer waste, have been expanded, often with no community notification and despite being in close proximity to homes and schools. Air quality suffers as the dumps release fumes from decomposing waste.
You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.

The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
If the garbage disposal won’t turn on, then it’s probably not getting power. First, make sure it’s plugged in. It’s easy to forget that disposals have wall outlets. It’s easy to knock a plug out of an outlet accidentally, especially in a dark place like under the sink. If the disposal is plugged in, check the reset button on the bottom of the disposal unit. If the disposal requires resetting, the button will be popped out. Simply press it and try the disposal again.

If the disposal is plugged in and doesn’t need to be reset, then you should check the circuit breaker. The breaker could be flipped, which would mean your disposal isn’t getting power. If that’s still not the problem, then either the outlet is dead, the circuit breaker is malfunctioning, or the disposal needs to be replaced. Check the outlet first by plugging something else into it. If the outlet works, try replacing the circuit breaker switch. If that isn’t it either, you have to replace the disposal.


Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.


Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.


Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
×