Manufactured in the United States, Waste King garbage disposals have won much praise for their energy efficient design. Waste King offers a wide range of garbage disposers for both residential and commercial settings. In the early 2000s, Waste King refocused their sights on providing unparalleled customer service and quality products, and their warranties are the current industry standard that others are measured by.
Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]

I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
In recent years, various Camorra clans have been forming alliances with Nigerian drug gangs and the Albanian mafia, even going so far as to intermarry.[citation needed] For instance, Augusto La Torre, the former La Torre clan boss who became a pentito, is married to an Albanian woman. It should also be noted that the first foreign pentito, a Tunisian, admitted to being involved with the feared Casalesi clan of Casal di Principe. The first town that the Camorra gave over to be completely governed by a foreign clan was Castel Volturno, which was given to the Rapaces, clans from Lagos and Benin City in Nigeria. This allowed them to traffic cocaine and women in sexual slavery before sending them across the whole of Europe.[33]

As the #1 faucet brand in North America, Moen offers a diverse selection of thoughtfully designed kitchen and bath faucets, showerheads, accessories, bath safety products, garbage disposals and kitchen sinks for residential and commercial applications each delivering the best possible combination of meaningful innovation, useful features, and lasting value.
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.

To preserve quality of life in the capital, the Moscow’s government sends streams of municipal waste into the surrounding regions. Greenpeace reports that 90 percent of Moscow’s waste goes to landfills in Moscow’s suburban region. Landfills created in the Soviet and early post-Soviet period, when there was little consumer waste, have been expanded, often with no community notification and despite being in close proximity to homes and schools. Air quality suffers as the dumps release fumes from decomposing waste.

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
If you’re unsuccessful using the wrench, you may need to go in through the drain in an attempt to remove the clog. Disconnect the power to the disposal by unplugging the unit or turning off its circuit breaker, then use long-handled tongs and a flashlight to try to remove the jam.  Never use your hands for this task, even if the disposal is completely disconnected from its power source! Fumbling blindly around a disc of sharp blades is asking for injury.

Garbage disposals first appeared in households in the 1930's and 1940's. These appliances, which are installed under a kitchen sink, can make a cook's life easier by trapping and shredding food waste items, allowing it to pass through the plumbing system. Although these popular appliances make cooking and cleaning much more convenient, they do require regular maintenance to keep them running at optimal performance. When it is time to replace your garbage disposal's blades, you can save time and money by doing it yourself.


The government has made an effort to combat the Camorra's criminal activities in Campania. The solution ultimately lies in Italy's ability to offer values, education and work opportunities to the next generation. However, the government has been hard pressed to find funds for promoting long term reforms that are needed to improve the local economic outlook and create jobs.[40] Instead, it has had to rely on limited law enforcement activity in an environment which has a long history of criminal tolerance and acceptance, and is governed by a code of silence or omertà that persists to this day.[41]
Your garbage disposal is one of the biggest helpers in your kitchen. Without it, cleaning up after quick weeknight dinners, family feasts, and leisurely Sunday breakfasts would be much harder. While some garbage disposal problems can be fixed with a quick repair, sometimes it’s easier and more cost-efficient to replace the appliance. If you’re not sure whether or not to replace or repair your garbage disposal, check out these five signs your appliance is completely broken.
Our testers found that differentiating features you'll typically see at the store may not deliver the durability they imply. We also found that some models with fewer features and a shorter warranty cost more than relatively similar competitors. Home garbage disposers typically last about 10 to 12 years, according to InSinkErator, though not all reach the decade mark. A longer warranty does not guarantee longer life and can also make some models cost more than otherwise-similar machines. Here are the garbage disposer features to consider:
Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.

For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
Waste disposal units may jam, but can usually be cleared either by forcing the turntable round from above or by turning the motor using a hex-key wrench inserted into the motor shaft from below.[25] Especially hard objects accidentally or deliberately introduced, such as metal cutlery, can damage the waste disposal unit and become damaged themselves, although recent advances, such as swivel impellers, have been made to minimize such damage.[citation needed] More problematic are drain blockages caused by shredded waste that is fibrous, e.g., artichoke leaves, or starchy, e.g., potato peelings.
×