Hang the disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. The disposal will now hang by itself. Tighten the three mounting screws, ultimately tightening each screw a few turns at a time until the mounting assembly is evenly and tightly seated against the bottom of the sink.
The size of the motor in the garbage disposal directly correlates to the units grinding ability. Garbage disposals typically have between 1/3-1 horsepower motors. Choose the correct horsepower based on the waste that you need to remove. 1/3 horsepower units will help tackle tasks like grinding vegetables easily, but more power is recommended if disposing a large quantity of food waste such as, vegetables and harder to grind meats.

The InSinkErator Badger 1 Continuous Feed Garbage Disposal 1/3 HP features a quick-mounting system that allows for easy installation or replacement. This sturdy garbage Disposal is constructed from galvanized steel and features a 26 oz. chamber for space-saving waste disposal. The garbage Disposal also features a 1/3 HP motor that rapidly grinds food waste for easy rinsing down the drain.
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.

Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.

Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.
Run your garbage disposal for longer each time you use it. A mistake many people make is turning off their garbage disposal as soon as the grinding noises stop. It is better to leave the garbage disposal on (with the water running) for several seconds after the grinding noises subside, as there may still be small particles in the disposal unit which have not yet been cleared away.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.


Chartered by entrepreneur Lowell Harrelson and Long Island mob boss Salvatore Avellino, it set sail on March 22 from Islip, New York,[2] escorted by the tugboat Break of Dawn and carrying 3,168 tons of trash headed for a pilot program in Morehead City, North Carolina, to be turned into methane. The barge was docked at Morehead City, until a WRAL-TV news crew, acting on a tip, flew by helicopter to the coast to investigate. Action News 5 Reporter Susan Brozek broke the story on the 6 p.m. news on April 1, 1987, and North Carolina officials began their own investigation, which resulted in an order for the Mobro to move on.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.

First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

Garbage Disposal Installation

×