Manufactured in the United States, Waste King garbage disposals have won much praise for their energy efficient design. Waste King offers a wide range of garbage disposers for both residential and commercial settings. In the early 2000s, Waste King refocused their sights on providing unparalleled customer service and quality products, and their warranties are the current industry standard that others are measured by.

While you’re inspecting your drain lines, also look to see if you see wear and tear. Over the years, drain lines can sprout leaks and cracks that can lose water. If you notice that your lines look pretty worn, you may want to have them replaced. Again, if you are inexperienced with home improvement projects, it’s best to call a professional to tackle the job.
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.

STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.

Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.

Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!
Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.

A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:
This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close
But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
Once you have a garbage disposer installed, maintenance is what keeps your unit going. By following this link, you will find a very easy to follow video which details some simple steps to help keep your disposal unit clean, and your kitchen free of bad smells and harmful bacteria. You see, my website isn’t just about telling you to buy this model or that right now or you’ll miss out on some good deals (although I have mentioned a couple of places you can take a look at if you’re interested), it’s about making sure you get the best from your garbage disposer.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).

The L-2600 garbage disposal unit is one of the brand’s best-sellers. Its glass-filled nylon grinding chamber allows a smoother and more quiet performance as opposed to a full stainless steel model. It’s also easy to install and doesn’t take up too much space. It even comes with a removable splash guard to keep all the food scraps down when disposing them.
Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.

Read the directions for your model before attempting a home repair. Most disposals have an electrical reset button, and a manual hex key for un-jamming. If the disposal stops working, its internal circuit breaker may have shut it off. Turn the switch definitely off, and try to pull out the hard object that may have jammed it. Then use the right-sized hex key to manually turn the rotor parts (usually directly under the unit in the center). If it turns, then push the reset button. It usually clicks in. Then, turn on the water and try the power, again.
Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.
The majority of today’s garbage disposals are designed to dovetail with a sink’s drain outlet, which makes connecting the two components simple. There are a multitude of connection kits and adaptors available. Many models feature a power cord that is simply plugged into a nearby outlet to power the unit; however, when an outlet is not available, the unit must be hardwired, which can be significantly more expensive.

If your garbage disposal is not running, first check to see if it is plugged in and receiving power. If so then check to see whether it will turn freely with your service wrench. Most disposers are sent with a self service wrench. The wrench is silver and should be located on or near your garbage disposal. (Check under your sink!) If it will not turn freely using the wrench, the disposal is most likely jammed. Check to see if the reset button has popped out.
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.

If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.


Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.

If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.


Since 2010, under the leadership of Mayor Sergei Sobyanin, Moscow has transformed into a dynamic global city, fueled by oil wealth and urban redevelopment. Moscow’s growing population and unfettered consumption mean increased waste. A report by the environmental group Greenpeace calculates that Moscow is responsible for 11 million tons of trash annually, approximately one-fifth of all waste in Russia. Only 4 percent of Moscow’s waste is recycled.

Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.
The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
×