Our most affordable large-capacity model ready to tackle Our most affordable large-capacity model ready to tackle meals of up to 750 persons with its powerful 3 HP motor. Like all InSinkErator food service disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as large banquet facilities ...  More + Product Details Close
If your garbage disposal is not running, first check to see if it is plugged in and receiving power. If so then check to see whether it will turn freely with your service wrench. Most disposers are sent with a self service wrench. The wrench is silver and should be located on or near your garbage disposal. (Check under your sink!) If it will not turn freely using the wrench, the disposal is most likely jammed. Check to see if the reset button has popped out.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Flush with water. Simply flushing out the garbage disposal with water will help to remove any loose dirt or grime. Stopper the garbage disposal, add a squirt of dish soap and run the hot water until there is 2 to 4 inches (5.1 to 10.2 cm) sitting in the sink. Pull out the plug and turn on the garbage disposal, allowing the water to flush through.[2]
Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.
I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?

Dishwasher Connection: Some disposals are connected to the dishwasher drain pipe, which drains leftover food removed from dishes going through the wash cycle. Leaks can sometimes occur in the hose connections where the disposal hose attaches to the dishwasher.Leaks can also happen if the seal on the hose is compromised or the clamp on the hose isn’t tight enough. If the connecting hose seems to be the source of the leak, try tightening the connection or replacing the seal. If neither solutions work, or the hose is obviously cracked, you will need to replace the hose.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.

Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.
Kitchen waste disposal units increase the load of organic carbon that reaches the water treatment plant, which in turn increases the consumption of oxygen.[28] Metcalf and Eddy quantified this impact as 0.04 pound of biochemical oxygen demand per person per day where disposers are used.[29] An Australian study that compared in-sink food processing to composting alternatives via a life cycle assessment found that while the in-sink disposer performed well with respect to climate change, acidification, and energy usage, it did contribute to eutrophication and toxicity potentials.[30]
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
InSinkErator garbage disposals provide a convenient and environmentally-conscious alternative to sending leftovers to landfills. Capable wastewater treatment plants can even recycle food scraps into energy and fertilizer. Plus, using garbage disposals can significantly reduce the amount of trash sent to landfills and reduce greenhouse gas emissions.
Once you have a garbage disposer installed, maintenance is what keeps your unit going. By following this link, you will find a very easy to follow video which details some simple steps to help keep your disposal unit clean, and your kitchen free of bad smells and harmful bacteria. You see, my website isn’t just about telling you to buy this model or that right now or you’ll miss out on some good deals (although I have mentioned a couple of places you can take a look at if you’re interested), it’s about making sure you get the best from your garbage disposer.
When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.

One of the handiest appliances in your kitchen is probably something that you don’t think about very often, until it stops working. It’s your garbage disposer, and today I’m going to show you how to replace a garbage disposer under your kitchen sink. This project requires some moderate do-it-yourself skills, and it also requires turning off the electricity to the disposer at the electrical panel. But it’s really not that difficult, so let’s get started.

Single Stream Recycling: Cedar Park was one of the first communities in central Texas to offer residents single-stream recycling. We began providing this service in February 2010. This has been incredibly successful; our average monthly recycling has jumped from 98 tons (when residents used the small blue bin) of diverted waste to 252 tons (now that residents have access to the larger 90 gallon bin)! 

If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.

Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.

First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
The Camorra received another blow with the Cuocolo trial (1911–1912). While the trial was about the murder of the Camorrista Gennaro Cuocolo and his wife, suspected of being police spies, on June 6, 1906, the main investigator, Carabinieri Captain Carlo Fabbroni, transformed it from a murder trial into one against the Camorra as a whole. Fabbroni intended to use the trial to strike the final blow to the Camorra.[20][21] The trial attracted a lot of attention of newspapers and the general public both in Italy as well as in the United States, including by Pathé's Gazette.[22] The hearings began in the spring of 1911 and would continue for twelve months. After a 17-month trial, the often tumultuous proceedings ended with a guilty verdict on July 8, 1912. The defendants, including 27 leading Camorra bosses, were sentenced to a total of 354 years' imprisonment. The main defendant and nominal head of the Camorra, Enrico Alfano, was sentenced to 30 years.[20][23][24][25]
Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
Modern food waste disposers are often connected to your dishwasher’s drain pipe. This connection enables your dishwasher to rid itself of any leftover food scraps or residue that it might accumulate while washing your dishes. Where the dishwasher hose and the garbage disposal connect is a common source for leaks. The leaks most often occur when hose’s clamp is not secure enough. Leaks also develop when the dishwasher hose cracks. In order to fix this type of leak, you should either replace the cracked section of hose or tighten the clamp down.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
×