If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).

Garbage Disposal Replacement


This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
We're expecting a lot of garbage disposal (waste disposal unit and garburator) service calls next week. Thanksgiving and Christmas are behind us, but another major celebratory gathering will take place this weekend. Although not an official holiday, the Super Bowl is considered a great American secular holiday by most. While many advocate for the day off on Super Bowl Monday, this will never happen for plumbers!

Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).
The evolution into more organized formations indicated a qualitative change: the Camorra and camorristi were no longer local gangs living off theft and extortion; they now had a fixed structure and some kind of hierarchy. Another qualitative leap was the agreement of the liberal opposition and the Camorra, following the defeat in the 1848 revolution. The liberals realized that they needed popular support to overthrow the king. They turned to the Camorra and paid them, the camorristi being the leaders of the city’s poor. The new police chief, Liborio Romano, turned to the head of the Camorra, Salvatore De Crescenzo, to maintain order and appointed him as head of the municipal guard.[11] The Camorra effectively had developed into power brokers in a few decades.[9] In 1869, Ciccio Cappuccio was elected as the capintesta (head-in-chief) of the Camorra by the twelve district heads (capintriti), succeeding De Crescenzo after a short interregnum.[12] Nicknamed 'The king of Naples' ('‘o rre 'e Napole) he died in 1892.[13][14]
Your garbage disposer is not draining, has water leaks, creates weird noises, or has horrible odors? Troubleshoot your Faulty Disposer. If you are experiencing garbage disposal problems, you will find solutions on our checklist below to help you repair it. Before going out and spending a few hundred dollars on a new one, troubleshoot your existing sink garbage disposer to find the problem.
Scotland has had its brush with the Camorra. Antonio La Torre of Aberdeen was the local "Don" of the Camorra. He is the brother of Camorra boss Augusto La Torre of the La Torre clan which had its base in Mondragone, Caserta. The La Torre Clan's empire was worth hundreds of millions of euros. Antonio had several legitimate businesses in Aberdeen, whereas his brother Augusto had several illegal businesses there. He was convicted in Scotland and is awaiting extradition to Italy. Augusto would eventually become a pentito in January 2003, confessing to over 40 murders and his example would be followed by many of his men.[54]

As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.


Copyright 2018 by Mr. Garbage Disposal. Mrgarbagedisposal.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. *Amazon and the Amazon logo are trademarks of Amazon.com, Inc., or its affiliates. Additionally, mrgarbagedisposal.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
Need Help?  Have a question or comment?1-888-827-4223Email UsGet Exclusive Offers & Expert TipsJOINTerms of UsePrivacy PolicyInterest Based AdsFor U.S. Residents Only © 2018 Ace Hardware. Ace Hardware and the Ace Hardware logo are registered trademarks of Ace Hardware Corporation. All rights reserved. For screen reader problems with this website, please call 1-888-827-4223 or email [email protected]
Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.
Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
As a general rule of thumb, the heavier and bigger that a garbage disposal is, the more quietly it will operate – so long as it fits properly underneath your sink. Even though the sound dampening technology used in the design of garbage disposals has improved dramatically in the last 10 years, it is unrealistic to expect your garbage disposal to operate noise free. Under specific sinks, some disposals will be noisier than others due to the amount of vibration they produce. Ideally, you should look for a garbage disposal that features a nylon, insulated grinding chamber, like those produced by WasteKing.
Most plumbing problems associated with holiday parties are caused by improper plumbing maintenance and overestimations of your plumbing system’s abilities. Although it’s best if you have a professional plumber inspect your system before any large gathering, many plumbing problems can be prevented with a little knowledge and preparation before the big day. Remember, the best offense is a good defense. Schedule annual plumbing maintenance to keep your entire plumbing system healthy and efficient. Current problems will be addressed and future problems will be detected.
Jarred Connections: Considering the garbage-disposal systems is located under the kitchen sink, and since the area under the kitchen sink is a common place for storing all sorts of things, it is fairly common for the unit to get bumped.If it gets hit hard enough, the unit can actually shift so that it is no longer sitting straight. Pipes can also get knocked around, causing the seals to lose effectiveness.
The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.

Locate the circuit breaker that controls power to the garbage disposal, and flip it to the "off" position before continuing. Fix or replace the main seal if it is leaking. Remove both the drain pipe and the dishwasher hose, if applicable. Insert a screwdriver into the tightening ring and turn it counterclockwise. This will release the garbage disposal unit. Inspect the main seal that sits on the top of the unit. The seal is a large, soft rubber fitting that covers the top edge of the garbage disposal. If dirt, grit or food particles have fouled the main seal, wipe it down with a damp rag and reinstall the disposal unit. If the main seal is cracked, pitted or broken, it needs to be replaced. Once a new main seal has been inserted into the garbage disposal, push it up against the mounting bracket, insert a screwdriver into the tightening ring, and turn it clockwise to lock the unit into place. Reinstall the drain pipe and dishwasher hose, if applicable.


STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!
If you're replacing a commercial garbage disposal, then you'll either want the Drain Strainer with Crown Adapter or the Drain Strainer XL. Both of these models have a universal Crown Adapter on top that serves as a funnel to cover the hole once the commercial garbage disposal has been removed. Note that it doesn't actually attach to the sink bowl, but you'll adjust the legs to get your unit flush underneath the bottom of the sink.
Installing a garbage disposal involves tapping into your home’s plumbing and electrical systems, and both systems need to be handled correctly to safely install your garbage disposal. Someone with a lot of experience can handle the job in 2 or 3 hours—or maybe even less. Attempting a garbage disposal installation without any training will likely take at least double the time required for a professional to install the garbage disposal.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.

Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
As the saying goes, an ounce of prevention is worth a pound of cure; in other words, take care of your garbage disposal to prevent leaks from happening. Proper use, regular maintenance and frequent inspections for leaks will keep your disposal in top working order. If you experience any water leaks or burst pipes, please call us and we will be happy to help.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
×