Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.
Discharge Pipe: The discharge pipe that goes into the drain of the sink is attached to the bottom of the garbage disposal. Either of these parts can sometimes loosen from regular use or may fail altogether with enough wear and tear.Check to be sure the connection is tight and tighten with a plumber’s wrench if necessary. If the discharge pipe still leaks, the seal that is located between the retaining nut and the discharge pipe may need to be replaced.
Your garbage disposal is one of the biggest helpers in your kitchen. Without it, cleaning up after quick weeknight dinners, family feasts, and leisurely Sunday breakfasts would be much harder. While some garbage disposal problems can be fixed with a quick repair, sometimes it’s easier and more cost-efficient to replace the appliance. If you’re not sure whether or not to replace or repair your garbage disposal, check out these five signs your appliance is completely broken.
Chartered by entrepreneur Lowell Harrelson and Long Island mob boss Salvatore Avellino, it set sail on March 22 from Islip, New York,[2] escorted by the tugboat Break of Dawn and carrying 3,168 tons of trash headed for a pilot program in Morehead City, North Carolina, to be turned into methane. The barge was docked at Morehead City, until a WRAL-TV news crew, acting on a tip, flew by helicopter to the coast to investigate. Action News 5 Reporter Susan Brozek broke the story on the 6 p.m. news on April 1, 1987, and North Carolina officials began their own investigation, which resulted in an order for the Mobro to move on.
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.
If your disposal grinds poorly, make sure that you are running enough water while operating the unit and that you are not grinding matter that you shouldn’t. If you can hear the garbage disposal running but it is not grinding, the blades may be broken. It’s usually easier and cheaper to just replace the entire unit. See How to Install a Garbage Disposal.
Some towns and cities require a homeowner to get a permit before being allowed to install a new food disposal system. Others have outright outlawed the use of disposals due to limited sewer and water capacity. For example, an increasing number of cities in California has banned the installation of new garbage disposers in homes due to the ongoing drought the state is suffering from.
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Garbage Disposal Repair or Replacement

×