Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!

So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.

Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close


Unlike the Sicilian Mafia, which has a clear hierarchy and a division of interests, the Camorra's activities are much less centralized. This makes the organization much more difficult to combat through crude repression.[39] In Campania, where unemployment is high and opportunities are limited, the Camorra has become an integral part of the fabric of society. It offers a sense of community and provides the youth with jobs. Members are guided in the pursuit of criminal activities, including cigarette smuggling, drug trafficking, and theft.[40]
I am a researcher. I read every review - the good and the bad. I've read the Consumer Reports reviews, read the Amazon reviews, read the other, sketchier review websites like GreatGarbageDisposals.com (I made that one up but if you've done any research on the internet you get my point). I am writing this review to share what I learned about the product and about the many reviews I've read. My situation was that our 6 year old Badger froze up and simply quit on me, so a new one was in order.
Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.

We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Michele Zagaria, a senior member of the Casalesi clan, was arrested in 2011 after eluding police for 16 years. He was found in a secret bunker in the town Casapesenna, near Naples.[44] In 2014, clan boss Mario Riccio was arrested for drug trafficking in the Naples area. Around the same time 29 suspected Camorra members were also arrested in Rome.[45]
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.
You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.

The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Most blog writers make money from the links they include, so if someone is reading this and decides to click on a link and purchase the item, they receive a small sales commission per se. Mind you it takes hundreds to thousands of these blogs ranking high in google searches (I’m sure you have an issue with most people using googleopoly as well) in order to make any real money at it, but until other brands get on the bandwagon and pay instead of hoping for free advertising, great bloggers will continue to use what pays the bills. Or at least kicks you back a free tank of gas or two a year.
In 2017, in Moscow and St. Petersburg, my research found a substantial increase in grassroots groups oriented around “civic pride” and local volunteer initiatives. These new groups focus on the preservation of green spaces, litter collection, recycling, urban beautification and historic preservation. These efforts represent a new “environmentalism of daily life” more acceptable to the government.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
After watching this video, I decided I could replace my garbage disposer myself. Honestly, I think your site completely misrepresents how VERY difficult it is to hold up a 20+ pound disposal unit firmly up against the mounting hardware as you are literally crammed under your kitchen sink and then try and somehow get all three tabs to slide into place. I was very disappointed and, after 4 nights of trying and retrying, finally just called a plumber. Please don’t show anyone lifting something that is big and heavy and make it seems as light as a feather. Shame. Shame.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
If the source is not a connection from above then your disposal needs to be replaced. Try cupping your hands around the very top under the sink while running water. The ring that seals the gasket turns clockwise to tighten. The only other repairable leak would be where the piping comes out the side. There can also be a smaller dishwasher drain hose above that.
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
AC AC Repair AC Replacement Air Conditioning Air Conditioning Maintenance Air Conditioning Replacement Alexandria Arlington Baltimore Bethesda Boiler Installation Boiler Repair Drain and Sewer Drain Cleaning Ductless Ductless AC Repair Ductless Air Conditioning Duct Sealing Fairfax Furnace Furnace Repair Gaithersburg Garbage Disposal Repair Heating Heat Pump Installation Heat Pump Maintenance Heat Pump Repair Heat Pumps HVAC Hyattsville Indoor Air Quality Pipe Inspection Plumbing Plumbing Maintenance Plumbing Repair Radiant Heating Rockville Silver Spring Springfield Washington Washington DC Water Heater Water Heater Maintenance Water Treatment Zone Control

If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.

Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.


If you’re like most people who cook, your kitchen probably looks like a disaster zone after preparing a meal for your family and eating it. The cleanup process is going to go much more quickly if you can stuff leftover food waste down the drain. Most garbage disposals have a switch located near the kitchen sink. All that you have to do is turn the faucet’s cold water on, flip the switch, and put the remaining leftovers in the drain.
Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
Here are some problems that every garbage disposal can run into, old or new. Learning about your garbage disposal and how it works (and how it doesn’t work, of course!) is the first step to decide if it simply needs a repair or if it needs to be replaced all together. One thing that stands for any and all situations: never stick your hands down the drain!

Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.
This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.
Food scraps range from 10% to 20% of household waste,[18] and are a problematic component of municipal waste, creating public health, sanitation and environmental problems at each step, beginning with internal storage and followed by truck-based collection. Burned in waste-to-energy facilities, the high water-content of food scraps means that their heating and burning consumes more energy than it generates; buried in landfills, food scraps decompose and generate methane gas; a greenhouse gas which contributes to climate change.[19]
×