Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
If the garbage disposal won’t turn on, then it’s probably not getting power. First, make sure it’s plugged in. It’s easy to forget that disposals have wall outlets. It’s easy to knock a plug out of an outlet accidentally, especially in a dark place like under the sink. If the disposal is plugged in, check the reset button on the bottom of the disposal unit. If the disposal requires resetting, the button will be popped out. Simply press it and try the disposal again.
This thing is exactly as everyone else has described. I, like many others, replaced an old ISE Badger with this unit, and it's heads and shoulders above in quality, function, quietness, etc. It grinds everything in seconds (as opposed to batting it around in the chamber for multiple cycles like the Badger). The original plumbing from the Badger lined right up and worked the first time. I'm very pleased with this item... although, there is one thing that I want to note; I read somewhere that if you use the EZ mount system that comes with it, you won't need plumber's putty - one can just use the gasket. This is true ONLY if using a flat lipped SS sink, and even then the rubber seal is optional as opposed to the putty (you can use only one, the putty or the seal with a SS sink, but not both). It's better said that you WILL need plumber's putty, and if you have a stainless steel sink, you have the option to use the thin rubber gasket (I'd use plumber's putty). Other than that minor detail (which made me take an unexpected run to our local hardware store), this unit is great. The one last thing I will say is around quietness. I've read some reviews that talk about how quiet or not quiet it is. I don't understand the desire to have an ultra-quiet garbage disposal. I mean, one needs to run water while the run the disposal, and a full-blast of the faucet going into a spinning basket creates a notable level of sound anyway, plus I want to be able to hear the load of the disposal so I can know when it's clear. This unit is by no means noisy, but I just don't see the desire to go ultra-quiet. Again, this big-boy Waste King is awesome.
The horror movie image of victims having hands and arms severed in a garbage disposal is entirely a Hollywood invention. In reality, the blades inside a garbage disposal are rather dull grinders, not gleaming, razor-sharp sabers. That is not to say that a disposal should be taken lightly—it is indeed possible to be painfully injured if you don't practice basic safety measures.
Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.
In 2008, Italian police arrested three members of the Camorra crime syndicate on September 30, 2008. According to Gianfrancesco Siazzu, commander of the Carabinieri police, the three were captured in small villas on the coast of Naples. All three had been on Italy's 100 top most wanted list. Police seized assets valued at over 100 million euros and also weapons, including two AK-47 assault rifles that may have been used in the shooting of six Africans on September 18, 2008. Police found pistols, Carabinieri uniforms and other outfits that were used to disguise members of the operation. During the same week, a separate operation netted 26 additional suspects in Caserta. All were believed to belong to the powerful Camorra crime syndicate that operates in and around Naples. The suspects were charged with extortion and weapons possession. In some cases, the charges also included murder and robbery. Giuseppina Nappa, the 48-year-old wife of a jailed crime boss, was among those arrested. She is believed to be the Camorra's local paymaster.
Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.
Some types of food remains are not easy to grind in a disposer. Do not put fibrous food items into your disposal. Help grind these items by putting in a few small bones or large ice cubes to the disposal. If the disposer won’t grind it up then turn off the disposer and remove the item with a pair of tongs. When using your disposer, make sure that the disposal is running with good water flow. Good water flow carries the waste down the drain line. Using too little water can create a clogged drain.
Have you ever opened the cabinets under the sink to remove the trash or a handful of cleaning products, only to find everything soaked and soggy? Have you ever installed – or even had professionally installed – a brand new, state-of-the-art garbage disposal, only to have it flood your kitchen floor the next day? If so, you have a major plumbing: a leaking garbage disposal leaking from.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
The snap ring fits into a groove on the lower end of the sink flange. When you’re working under the sink, it prevents the upper mounting bracket from falling off. Removing an old snap ring can be frustrating-unless you know this trick: Starting at the break in the ring, insert a thin-blade screwdriver between the ring and the flange. Pull down on the ring with the screwdriver’s blade and walk the blade around the ring. The ring will pop right off.
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water
A: A leaking garbage disposal often goes unnoticed until you confront a sopping cabinet, a foul-smelling puddle, or an audible drip-drip-drip from the unit. The fix can be frustrating, too, because the leak can stem from a number of components in the system. Fortunately, with a little sleuthing, you can zero in on the leak and—depending on the exact location—stop the icky oozing and repair the component that caused it. Worst case scenario, if it turns out that the garbage disposal must be replaced, installing a new one is a reasonable do-it-yourself task for those with basic plumbing skills. Read on to keep the cash you’d otherwise hand over to a pro.
Why am I writing a review about my beloved garbage disposal? Why am I referring to it as my "beloved" garbage disposal? I replaced a different garbage disposal from Costco; it had lasted a few years before giving up the ghost (the metal teeth within had basically corroded and broken off). Even before it met its untimely end, it had been loud and took a long time to grind things up--despite it being 1-1/4 horsepower!
If your garbage disposal is not running, first check to see if it is plugged in and receiving power. If so then check to see whether it will turn freely with your service wrench. Most disposers are sent with a self service wrench. The wrench is silver and should be located on or near your garbage disposal. (Check under your sink!) If it will not turn freely using the wrench, the disposal is most likely jammed. Check to see if the reset button has popped out.
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.