If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Garbage Disposal Repair or Replacement


Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.

IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.

In the United States, almost all garbage disposals on the market are manufactured by a handful of companies; although, many are branded under different names. For example, out of the top ten highest rated models on the market, InSinkErator makes eight of them. Whirlpool and WasteKing are the other two most well-known brands in the U.S. There are a wide range of models to choose from, ranging from basic $50.00 models to models equipped with all of the latest bells and whistles that can cost as much as $600.00. In most cases, you get what you pay for in terms of quality. Here is a brief overview of the top brands in the U.S.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.

Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.


Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.
There are many potential causes for a leaky garbage disposal.  Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable.  Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.
Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.
STEP 5 – If you are one of those rebellious types that never listens to wise instruction, then take off any rings and make sure that your hand is lubricated with liquid dish soap or cooking oil to reduce the risk of it getting stuck in the drain opening. Also, have a phone nearby. If your hand does get stuck, you can then call someone (using your other hand, presumably) to call a friend or 911 for rescue. If at all possible, don’t call a friend with a video camera phone, because they’ll probably embarass you by broadcasting your plight on YouTube.
Connect the connector pipe to the elbow and the adjacent sink. Use the connector pipe to connect the elbow piece to the T-fitting on the adjacent sink. The connector piece might need to be cut down to the correct length depending on your sink. Use the nuts and washers provided with your pipes to secure the pieces together using the tongue-and-groove pliers.[1]

A broken garbage disposal makes tackling your to-dos an unnecessary challenge, which is why the experts at Sansone want to help. Whether your garbage disposal is leaking, clogged, humming, or completely stuck, we can repair the issue or replace your garbage disposal entirely. Contact us today with any plumbing questions or schedule an appointment that’s convenient for you by phone or on our website.

Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.

The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
This is the best replacement garbage disposal stopper thingie I've ever purchased. It is also the only garbage disposal stopper thingie that I've ever purchased. But it does the job, it fits the sink perfectly, and it reduces my fear that when the garbage disposal is turned on that it may launch a penny or other metal missile that had accidentally dropped into the sink at supersonic speed toward my head.
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
After you install the new sink flange, you don’t want it shifting around when you’re assembling the parts underneath. Movement of the flange could break the seal between the flange and the sink, inviting a leak. Your best bet is to ask a helper to press down on the sink flange, or if you’re working alone, find something to weigh it down, such as the old disposal. Place an old towel under the weight so you don’t scratch the sink. If the bottom of your sink is quite concave, the old disposal might not contact the flange. In that case, place a can on the flange, then weigh down the can.
The bulk of a food waste disposer system, which includes the seals and pipes, is located beneath the kitchen sink. Most homeowners use this space to store various items, and it is not uncommon for people to bump or jar the disposal’s pipes when reaching for an item that is in close proximity. If the pipes are struck hard enough, the pipes can shift so that they are no longer sitting properly. Retaining bolts can become loose. Pipes may move, and seals can shift into an awkward position.
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.
×