A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.

This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close

InSinkErator garbage disposals provide a convenient and environmentally-conscious alternative to sending leftovers to landfills. Capable wastewater treatment plants can even recycle food scraps into energy and fertilizer. Plus, using garbage disposals can significantly reduce the amount of trash sent to landfills and reduce greenhouse gas emissions.


Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
However, if your garbage disposal is fairly new, having the reset button repaired is a better choice, especially if your unit is still under warranty. If your unit is under warranty, the company will probably send out a repair man to fix the job. On the other hand, if your unit isn’t under warranty, it’s best to have a skilled technician complete the job unless you have experience doing this.
If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.
A: A leaking garbage disposal often goes unnoticed until you confront a sopping cabinet, a foul-smelling puddle, or an audible drip-drip-drip from the unit. The fix can be frustrating, too, because the leak can stem from a number of components in the system. Fortunately, with a little sleuthing, you can zero in on the leak and—depending on the exact location—stop the icky oozing and repair the component that caused it. Worst case scenario, if it turns out that the garbage disposal must be replaced, installing a new one is a reasonable do-it-yourself task for those with basic plumbing skills. Read on to keep the cash you’d otherwise hand over to a pro.
Our Minneapolis – St. Paul plumbers assist customers with garbage disposal installation by helping them choose between a continuous feed garbage disposal or a batch feed utility. Our plumbers will discuss the best options for your home and lifestyle. Some of the benefits of our garbage disposals include anti-jamming technology, plastic or metal blades, connectors to the dishwasher, system quietness, and more.

If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.


Your garbage disposal is one of the biggest helpers in your kitchen. Without it, cleaning up after quick weeknight dinners, family feasts, and leisurely Sunday breakfasts would be much harder. While some garbage disposal problems can be fixed with a quick repair, sometimes it’s easier and more cost-efficient to replace the appliance. If you’re not sure whether or not to replace or repair your garbage disposal, check out these five signs your appliance is completely broken.
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.
You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.
While inspecting your unit, if you see leaking, you will need to equip yourself with a screwdriver and tighten up the clamp that’s holding the garbage disposal to the dishwasher. The smaller drain line is attached by screws. Tighten up these screws and if the gasket is worn, replace this too (Careful not to overtighten). You should be able to purchase gaskets at your local home improvement store for a fairly inexpensive price.
Run your garbage disposal for longer each time you use it. A mistake many people make is turning off their garbage disposal as soon as the grinding noises stop. It is better to leave the garbage disposal on (with the water running) for several seconds after the grinding noises subside, as there may still be small particles in the disposal unit which have not yet been cleared away.
3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.
I did all the things that you said. I finallyt called the home warrenty company. They said that there was a penny stuck and I had to get a new disposal. He took a pciture so I could see. I asked him why he didnt try to get the penny out and he said that he would just replace After he left, I put my hand in to see if I could get the penny lose. I could not see it so I put my hand in again and got all the food out and there was the penny. I then tried to get it to run and it is still humming. What should i do? Do I really need a new disposal?
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
GE, which is an acronym for General Electric, is an international conglomerate whose headquarters are based in New York City, New York. The company operates in many different segments, ranging from home appliances to transportation. In terms of gross revenue, GE is the sixth largest company firm in the United States. GE garbage disposals have won praise for their powerful motors and overall durability.
Garbage disposals first appeared in households in the 1930's and 1940's. These appliances, which are installed under a kitchen sink, can make a cook's life easier by trapping and shredding food waste items, allowing it to pass through the plumbing system. Although these popular appliances make cooking and cleaning much more convenient, they do require regular maintenance to keep them running at optimal performance. When it is time to replace your garbage disposal's blades, you can save time and money by doing it yourself.
Once you have a garbage disposer installed, maintenance is what keeps your unit going. By following this link, you will find a very easy to follow video which details some simple steps to help keep your disposal unit clean, and your kitchen free of bad smells and harmful bacteria. You see, my website isn’t just about telling you to buy this model or that right now or you’ll miss out on some good deals (although I have mentioned a couple of places you can take a look at if you’re interested), it’s about making sure you get the best from your garbage disposer.

Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
×